1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Brandmotion Universal 4-Sensor Switchable Front or Rear Parking Sensor System (Model 9002-3010). This system is designed to assist drivers in avoiding common parking accidents by providing distance detection and audible alerts.
2. Safety Information
Always exercise caution when parking. This system is an aid and should not replace careful driving and visual inspection of your surroundings. Ensure all connections are secure and properly insulated to prevent electrical hazards. Professional installation is recommended for optimal safety and performance.
3. Package Contents
Verify that all components are present before beginning installation:
- 4 Ultrasonic Sensors
- LED Display Unit
- Speaker Unit
- Electronic Control Unit (ECU)
- Sensor Harness (4 feet)
- Switch Cable (5 feet)
- Speaker Cable (5 feet)
- Body Harness (8 feet)
- Display Extension Cable (8 feet)
- Mounting Hardware (as applicable for tape-in/drill-in)
4. Setup and Installation
The Brandmotion 9002-3010 system can be installed on either the front or rear of your vehicle. It is compatible with both steel and plastic bumpers. Professional installation is highly recommended. DIY installation typically takes 180-240 minutes, while professional installation is estimated at 120-180 minutes.
4.1 Sensor Mounting
- Plastic Bumpers: Sensors are designed for rear tape-in mounting.
- Metal Bumpers: Sensors are designed for front drill-in mounting.
- Consult an automotive paint technician if you wish to customize the sensor color.
Image 1: Example of the four ultrasonic parking sensors. These sensors are designed for flush mounting into the vehicle's bumper.
4.2 Wiring Connections
- Connect the 4' Sensor Harness from the body harness to the driver side sensor.
- Connect the 5' Switch Cable to the Electronic Control Unit (ECU).
- Connect the 5' Speaker Cable to the ECU.
- Connect the 8' Body Harness from the ECU to the vehicle's power source and other necessary connections.
- Connect the 8' Display Extension Cable to the LED Display Unit and the ECU.
Image 2: The Electronic Control Unit (ECU) with a barcode label F20230801218. This unit processes sensor data and controls the display and speaker.
5. Operating Instructions
Once installed, the parking sensor system provides visual and audible feedback to assist with parking maneuvers.
5.1 LED Display Unit
Image 3: The LED display unit. It shows numerical distance to an object and uses color-coded segments (green, yellow, red) to indicate proximity.
- The display shows the distance to the nearest object numerically.
- Color-coded segments (green, yellow, red) illuminate to visually represent proximity. Green indicates a safe distance, yellow indicates caution, and red indicates very close proximity.
5.2 Audible Alert Speaker
Image 4: The speaker unit, visible as part of the display assembly. It features a switch with 'Off', 'Lo' (Low), and 'Hi' (High) volume options.
- The speaker emits an audible alert that increases in frequency as your vehicle approaches an object.
- The speaker unit features a switch with "Off", "Low", and "High" volume options to suit user preference.
6. Maintenance
To ensure optimal performance and longevity of your parking sensor system:
- Keep sensors clean from dirt, snow, ice, and debris. Obstructions can lead to inaccurate readings.
- Periodically check all wiring connections for security and signs of wear.
- Avoid using harsh chemicals or abrasive materials when cleaning the sensors or display unit.
7. Troubleshooting
If you experience issues with your parking sensor system, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Inconsistent or False Alerts |
|
|
| No Display or Audible Alert |
|
|
| Display Shows Incorrect Distance |
|
|
8. Specifications
- Model: 9002-3010
- Sensor Type: 4 Ultrasonic Sensors
- Operation: Front or Rear (Switchable)
- Display: High-Quality LED, Numerical and Color-Coded
- Alerts: Audible, increasing frequency with proximity
- Speaker Options: Off, Low, High
- Sensor Harness Length: 4 feet
- Switch Cable Length: 5 feet
- Speaker Cable Length: 5 feet
- Body Harness Length: 8 feet
- Display Extension Cable Length: 8 feet
- UPC: 819779022409
- Product Dimensions (Packaging): 9.75" L x 7.25" W x 2.5" H
- Product Weight (Packaging): 1.65 lbs
9. Warranty and Support
For warranty information or technical support, please contact Brandmotion customer service. Keep your proof of purchase for warranty claims.
Brandmotion Contact: Refer to the official Brandmotion website or your product packaging for the most current contact information.
Online Resources: Visit the Brandmotion Store on Amazon
