SPEDWHEL Original Dashboard for Ninebot MAX G30D KickScooter Electric Scooter Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the SPEDWHEL Original Dashboard for the Ninebot MAX G30D Electric KickScooter. This dashboard serves as a replacement or upgrade component, displaying essential information such as speed, riding mode, and battery status. Please read this manual thoroughly before proceeding with installation or use to ensure proper function and safety.

2. Safety Information

Always prioritize safety when working with electronic components and electric scooters. Failure to follow these safety guidelines may result in damage to the product, the scooter, or personal injury.

• Disconnect Power: Before beginning any installation or maintenance, ensure the electric scooter is completely powered off and disconnected from any charging source.
• Professional Installation Recommended: If you are not confident in your technical abilities, seek assistance from a qualified technician.
• Handle with Care: Electronic components are delicate. Avoid dropping, bending, or applying excessive force to the dashboard or its connectors.
• Moisture Protection: Keep the dashboard and its connections dry. Exposure to water or excessive humidity can cause damage.
• Use Correct Tools: Employ appropriate tools for disassembly and assembly to prevent stripping screws or damaging parts.

3. Package Contents

Verify that all items are present and in good condition upon opening the package.

• SPEDWHEL Original Dashboard Assembly for Ninebot MAX G30D

Figure 3.1: The dashboard assembly as received in its packaging, showing the part number 14.02.0315.00.

4. Setup and Installation

This section outlines the steps for installing the new dashboard. It is recommended to consult a service manual for your Ninebot MAX G30D for detailed scooter disassembly instructions if you are unfamiliar with the process.

4.1. Tools Required

• Screwdriver set (Phillips head, Torx may be required depending on scooter model)
• Plastic pry tools (optional, for delicate panel removal)

4.2. Installation Steps

1. Power Off Scooter: Ensure the Ninebot MAX G30D is completely powered off and unplugged from any charging source.
2. Access Dashboard Area: Carefully remove the handlebar cover or any panels that obstruct access to the existing dashboard. Refer to your scooter's service manual for specific disassembly instructions.
3. Disconnect Old Dashboard:
   

   Figure 4.1: Front view of the dashboard showing the main connector (left) and various wire harnesses (right).

   

   Figure 4.2: Close-up of the main blue connector, which connects the dashboard to the scooter's main wiring harness.

   

   Figure 4.3: Close-up of the smaller wire harnesses, typically connecting to various scooter components like lights and controls.

   Carefully disconnect all wire harnesses from the old dashboard. This typically includes a main connector (often blue, as shown in Figure 4.2) and several smaller connectors for various functions (Figure 4.3). Note the orientation and connection points of each wire harness for reassembly.
4. Remove Old Dashboard: Unscrew or unclip the old dashboard from its housing.
5. Install New Dashboard: Place the new SPEDWHEL dashboard into the housing. Ensure it fits securely.
6. Connect New Dashboard:
   

   Figure 4.4: Rear view of the dashboard circuit board, showing the connection points for the wire harnesses.

   Connect all wire harnesses to the new dashboard, matching them to their corresponding ports. Refer to Figure 4.4 for the general layout of the circuit board and connection points. Ensure all connections are firm and correctly seated.
7. Test Functionality: Before reassembling the scooter, temporarily power it on to verify that the new dashboard lights up and displays information correctly. Power off the scooter after testing.
8. Reassemble Scooter: Carefully reattach any covers or panels removed during disassembly. Ensure all screws are tightened appropriately.

5. Operating Instructions

The dashboard provides real-time information about your scooter's status. Familiarize yourself with the display indicators:

Figure 5.1: The dashboard display showing various indicators.

• Speed Display: Shows current speed in either kilometers per hour (km/h) or miles per hour (mph).
• Riding Modes:
  • ECO: Economy mode, typically for extended range and lower speed.
  • D: Drive mode, standard operating mode.
  • S: Sport mode, for maximum speed and acceleration.
• Headlight Indicator: Illuminates when the scooter's headlight is active.
• Bluetooth Indicator: Illuminates when the scooter's Bluetooth is connected or discoverable.
• Battery Level: Indicated by a series of bars, showing the remaining charge.
• Error Codes: In case of a malfunction, the display may show specific error codes. Refer to your scooter's main user manual for a list of error codes and their meanings.

To switch between riding modes or perform other functions, use the scooter's control buttons as described in your Ninebot MAX G30D user manual. The dashboard itself is a display unit and does not typically have user-operable buttons for mode changes.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your dashboard.

• Cleaning: Use a soft, dry, or slightly damp cloth to wipe the display surface. Avoid abrasive cleaners, solvents, or excessive moisture, which can damage the screen or internal components.
• Protection: While designed for outdoor use, avoid prolonged direct exposure to harsh sunlight, extreme temperatures, or heavy rain.
• Inspections: Periodically check the connections to ensure they remain secure and free from corrosion.

7. Troubleshooting

If you encounter issues with your dashboard, try the following basic troubleshooting steps:

• Dashboard Not Turning On:
  • Ensure the scooter is powered on.
  • Check all wire connections to the dashboard (refer to Section 4.2). Ensure they are firmly seated.
  • Verify the scooter's battery has sufficient charge.
• Incorrect Speed/Mode Display:
  • This may indicate an issue with the scooter's main controller or sensors, not necessarily the dashboard itself. Consult your scooter's service manual or a qualified technician.
• Display Flickering or Malfunctioning:
  • Power cycle the scooter (turn off, wait 30 seconds, then turn on).
  • Check for loose connections.
  • If the issue persists, the dashboard may be faulty and require replacement.

For issues not resolved by these steps, contact SPEDWHEL customer support or a certified Ninebot service center.

8. Specifications

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or SPEDWHEL customer service directly. Keep your purchase receipt as proof of purchase.

Seller: hulixia

Amazon Seller Link: hulixia on Amazon