ReplacementScrews RSAZN4321868

ReplacementScrews Shelf Hex Screws Instruction Manual

Compatible with Target 6 Cube Organizer (Brightroom 13in Cubes)

1. Product Overview

This manual provides essential information for the proper use and compatibility of ReplacementScrews Hex Screws, designed specifically for the Target Brightroom 13-inch 6 Cube Organizer Storage Shelf System. These screws are intended as replacement or assembly components to ensure the structural integrity of your shelving unit.

Eight zinc-plated hex screws laid out in a row on a white background.

Figure 1: A complete set of eight zinc-plated hex screws, essential for assembling or replacing components in compatible cube organizers.

2. Package Contents

Each pack contains the following components:

  • Eight (8) Zinc Plated Confirmat Furniture Screws: These screws are approximately 3-1/4 inches long, feature a flat head, and require a hex drive for installation.

Note: A 4mm Allen key is required for assembly but is not included in this package. Wooden dowels are also not included.

3. Compatibility

These hex head screws are specifically designed for compatibility with the Target Six (2 x 3) Cube Organizer Shelves that measure approximately 30 inches (H) x 43.8 inches (W) x 14.6 inches (D). It is crucial to verify that your organizer is the larger 13-inch cube shelf with thick outer panels, and not the smaller 11-inch system.

Compatible with the following Target Brightroom styles and item numbers:

  • Styles: BR21-006-013, BR21-006-001, BR21-006-014, BR21-006-003, BR21-006-002
  • Item Numbers: 002-11-0456, 002-11-0057, 002-11-0455, 002-11-0049, 002-11-0461

Please note: These are compatible assembly screws and are not Original Equipment Manufacturer (OEM) parts.

Close-up view of seven zinc-plated hex screws, showing the flat head and hex drive.

Figure 2: Detail of the hex screws, highlighting their flat head and hex drive design.

4. Setup and Installation

These screws are used for the assembly or re-assembly of the compatible Target Brightroom 13-inch 6 Cube Organizer. Follow the original assembly instructions provided with your cube organizer, replacing any damaged or missing screws with these ReplacementScrews components.

  1. Identify Screw Locations: Refer to your organizer's assembly manual to locate the designated screw points.
  2. Prepare Tools: Ensure you have a 4mm Allen key (hex wrench) readily available.
  3. Insert Screws: Align the screw with the pre-drilled hole in the organizer panels.
  4. Tighten Screws: Use the 4mm Allen key to turn the screw clockwise until it is firmly seated. Do not overtighten, as this may damage the particle board material of the organizer.

Ensure all eight screws are used for complete assembly to maintain the structural integrity of the 6-cube organizer.

5. Maintenance

These zinc-plated screws are designed for durability. No specific maintenance is required for the screws themselves. However, it is recommended to periodically check the tightness of all screws in your cube organizer to ensure stability and prevent loosening over time. If any screw appears loose, gently retighten it with a 4mm Allen key.

6. Troubleshooting

  • Screws do not fit:
    • Verify that your Target cube organizer is the 13-inch cube size, not the 11-inch. These screws are specifically for the larger model.
    • Confirm the model and style numbers of your organizer against the compatibility list in Section 3.
  • Screws are difficult to tighten:
    • Ensure you are using the correct tool (4mm Allen key).
    • Check that the screw is properly aligned with the pre-drilled hole. Do not force the screw.
  • Organizer feels wobbly after assembly:
    • Ensure all eight screws are installed and fully tightened.
    • Verify that all panels of the organizer are correctly aligned and seated.
Eight zinc-plated hex screws standing upright in a row, showcasing their length and head design.

Figure 3: The eight hex screws displayed upright, illustrating their full length and consistent design.

7. Specifications

AttributeDetail
Product NameReplacementScrews Shelf Hex Screws
Model NumberRSAZN4321868
MaterialZinc
Exterior FinishZinc Plated
Head StyleFlat, Hex
Drive SystemExternal Hex (requires 4mm Allen key)
LengthApproximately 3-1/4 inches
Thread Size4-40 UNC
Package Dimensions5.35 x 2.99 x 0.98 inches
Weight4.94 ounces
ManufacturerReplacementScrews
ASINB0BX4WDTCQ
Date First AvailableFebruary 28, 2023

8. Warranty Information

Specific warranty details for this product are not provided in the available information. For any warranty-related inquiries, please contact the manufacturer directly.

9. Customer Support

For further assistance, questions, or concerns regarding your ReplacementScrews product, please visit the official ReplacementScrews Store on Amazon:

Visit ReplacementScrews Store

You may also refer to the product listing on Amazon for additional details and customer reviews.

© 2023 ReplacementScrews. All rights reserved.

Product Model: RSAZN4321868

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.