Introduction
The Thermaltake SWAFAN EX 12 RGB PC Cooling Fan is designed to provide efficient cooling and vibrant RGB lighting for your desktop PC. This 3-pack features an innovative magnetic connection system for streamlined installation and cable management, along with swappable fan blades to optimize airflow direction. This manual will guide you through the setup, operation, and maintenance of your SWAFAN EX 12 RGB fans.
What's in the Box
The SWAFAN EX 12 RGB 3-Pack includes the following components:
- 3 x SWAFAN EX 12 RGB Fan Frames
- 3 x Standard Fan Blades (Pre-installed)
- 3 x Reverse Fan Blades
- 1 x Fan Controller
- 3 x Magnetic Connection Cables (Mag-cables)
- Mounting Screws and Accessories
Image: Overview of the Thermaltake SWAFAN EX 12 RGB PC Cooling Fan 3-Pack.
Setup and Installation
Follow these steps to install your Thermaltake SWAFAN EX 12 RGB fans:
1. Magnetic Fan Connection
The SWAFAN EX fans feature a magnetic force design for easy connection. Align the fans side-by-side, and they will snap together securely, forming a daisy-chain. This reduces the number of cables needed for multiple fans.
Image: Demonstrates the magnetic connection between multiple SWAFAN EX fans.
2. Swapping Fan Blades
The SWAFAN EX fans come with swappable fan blades, allowing you to easily change the airflow direction (push or pull) without reorienting the entire fan. To swap blades:
- Gently twist and pull the pre-installed standard fan blade from the fan frame.
- Align the desired reverse fan blade with the motor hub and push it firmly until it clicks into place.
Image: Illustration of airflow direction for standard (push) and reverse (pull) fan blades.
3. Connecting the Controller and Cables
Connect the magnetic connection cable to the last fan in your daisy chain. Ensure the cable is securely attached. The controller requires a USB 2.0 header (9-pin) on your motherboard for data communication and a SATA power connector from your power supply for power.
- Connect the magnetic cable from the fan chain to the controller.
- Connect the USB 2.0 cable from the controller to an available USB 2.0 header on your motherboard.
- Connect the SATA power cable from your power supply to the controller.
Image: A single SWAFAN EX 12 RGB fan, highlighting its design and connectivity.
4. Mounting the Fans
Mount the assembled fan units into your PC case or onto your radiator using the provided screws. Ensure proper alignment and secure fastening.
Video: Official Thermaltake guide on installing SWAFAN EX fans, demonstrating magnetic connections and cable routing.
Operating Instructions
The SWAFAN EX 12 RGB fans offer versatile control options for both fan speed and RGB lighting.
1. TT RGB PLUS 2.0 Software
Download and install the FREE TT RGB PLUS 2.0 Software from the Thermaltake website. This software allows for comprehensive control over fan speeds, RGB lighting effects, and customization of individual LED profiles. The software supports dual-zone RGB control, with 14 LEDs on the outer ring and 6 LEDs on the inner ring.
2. Fan Controller (Included)
The included controller provides basic control over RGB lighting effects. Refer to the software for advanced customization.
Video: Official Thermaltake overview of the Swafan EX RGB PC Cooling Fan, showcasing its features and RGB lighting.
Maintenance
Regular cleaning of your SWAFAN EX fans is recommended to maintain optimal performance and aesthetics.
Cleaning Fan Blades
The swappable fan blade design makes cleaning easy. You can remove the fan blades and rinse them with water. Ensure they are thoroughly dried before reattaching them to the fan frame. Apply bearing lubricant if needed (not included).
Image: A hand rinsing a SWAFAN EX fan blade under running water, demonstrating ease of cleaning.
Troubleshooting
If you encounter issues with your SWAFAN EX 12 RGB fans, consider the following:
- Fans Not Spinning or Lighting Up: Check all magnetic connections between fans and ensure the main magnetic cable is firmly connected to the controller. Verify that the controller has proper SATA power and USB 2.0 connections to the motherboard.
- RGB Malfunction: Ensure the TT RGB PLUS 2.0 software is installed and updated. Check the 5V ARGB connection from the controller to the motherboard. Re-seat all connections if necessary.
- Fan Speed Issues: Confirm that the fan cable is correctly connected to the controller and the controller to the motherboard's USB 2.0 header. Adjust fan curves within the TT RGB PLUS 2.0 software.
- Loose Connections: If fans feel loose or connections are intermittent, ensure the magnetic connections are fully engaged and the mounting screws are tightened appropriately.
Specifications
| Feature | Specification |
|---|---|
| P/N | CL-F143-PL12SW-A |
| Fan Dimension | 120 x 120 x 25 mm |
| Interface | USB 2.0 connectors (9 Pin) |
| System Compatibility | Windows 10 / 11 |
| Fan Started Voltage | 9.0 V |
| Fan Rated Voltage | 12 V & 5V |
| Rated Current (one fan) | 12 V - 0.23 A, 5 V - 0.72 A |
| Power Input (one fan) | 12 V - 2.76 W, 5 V - 3.6 W |
| Fan Speed | 500 ~ 2000 R.P.M |
| Max. Air Pressure (Standard Fan Blade) | 2.39 mm-H2O |
| Max. Air Pressure (Reverse Fan Blade) | 2.02 mm-H2O |
| Max Air Flow (Standard Fan Blade) | 57.11 CFM |
| Max Air Flow (Reverse Fan Blade) | 56.26 CFM |
| Noise Level (Standard Fan Blade) | 30.6 dB-A |
| Noise Level (Reverse Fan Blade) | 32.5 dB-A |
| Bearing Type | Hydraulic Bearing |
| Life Expectation | 40,000 hrs, 25℃ |
Warranty and Support
Thermaltake products are designed for reliability and performance. For warranty information and technical support, please visit the official Thermaltake website or contact their customer service. Keep your proof of purchase for warranty claims.
For further assistance, please refer to the Thermaltake Official Website.
