Bellemave L-Shaped Bunk Bed with Storage Stairs, Twin Over Full & Twin Loft Bed - Instruction Manual

1. Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your Bellemave L-Shaped Bunk Bed. This bed system features a twin over full bunk bed combined with a twin size loft bed, integrated storage stairs, and three under-bed drawers. Please read all instructions carefully before assembly and use to ensure safe and proper installation.

Figure 1.1: Overview of the Bellemave L-Shaped Bunk Bed in an espresso finish.

2. Safety Information

Adherence to these safety guidelines is crucial for preventing injury and ensuring the longevity of your bunk bed. Failure to follow these instructions may result in serious injury.

• Read All Instructions: Ensure all assembly steps are followed precisely.
• Weight Limits: Be aware of and adhere to the weight limits for each bed section. Overloading can cause structural failure.
• Guardrails: The upper bunk features a full-length guardrail. Ensure it is always securely in place.
• Ladder/Stairs Safety: Always use the provided ladders and stairs for access to the upper bunks. Do not jump on or off the beds.
• Mattress Compatibility: Use only mattresses of the specified size and thickness to ensure guardrail effectiveness. No box spring is needed.
• Regular Checks: Periodically check all bolts and connections to ensure they remain tight. Retighten as necessary.
• Pinch Points: Exercise caution during assembly and use, as the product may have pinch points or sharp edges.
• Ventilation: Ensure adequate ventilation around the bed, especially for the upper bunk.
• Children's Safety: Do not allow children under 6 years of age on the upper bunk.

Figure 2.1: Close-up of the integrated storage stairs and upper bunk guardrail, highlighting safety features.

3. Package Contents

Before beginning assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact customer support.

• Twin Over Full Bunk Bed Frame components
• Twin Size Loft Bed Frame components
• Integrated Storage Stairs unit
• Three Under-Bed Drawers
• Wooden Slats for all bed sections
• Guardrails for upper bunks
• Assembly Hardware (bolts, screws, nuts, etc.)
• Assembly Tools (usually an Allen wrench)
• Instruction Manual (this document)

Figure 3.1: The three under-bed drawers, part of the package contents.

4. Assembly Instructions

Assembly requires at least two adults. Clear a large area for assembly and keep all parts organized. Do not fully tighten bolts until instructed to do so.

1. Unpack and Identify Parts: Carefully unpack all components and lay them out. Refer to the parts list in your physical manual to identify each piece.
2. Assemble the Twin Over Full Bunk Bed Base: Begin by assembling the headboards, footboards, and side rails for the twin over full bunk bed. Ensure all connections are secure but do not overtighten.
3. Attach Slats to Twin Over Full Bunk Bed: Install the wooden slats onto the bed frames. Ensure even spacing and secure attachment.
4. Assemble the Twin Size Loft Bed Base: Follow similar steps to assemble the twin size loft bed frame, including its headboard, footboard, and side rails.
5. Attach Slats to Twin Size Loft Bed: Install the wooden slats for the loft bed.
6. Assemble Storage Stairs: Construct the integrated storage stairs unit. Ensure drawers slide smoothly into their compartments.
7. Connect Bed Sections: Carefully position and connect the twin over full bunk bed, the twin size loft bed, and the storage stairs unit to form the L-shaped configuration. Refer to the overall diagram for correct orientation.
8. Install Guardrails and Ladders: Securely attach the guardrails to the upper bunks and install the ladders for access.
9. Install Under-Bed Drawers: Place the three under-bed drawers beneath the full-size bed.
10. Final Tightening: Once all components are in place and aligned, systematically tighten all bolts and screws. Do not overtighten.

Figure 4.1: Overall dimensions and layout of the L-shaped bunk bed system.

Figure 4.2: Side view illustrating the under-bed drawers and bed structure.

Figure 4.3: Detail of the wooden slats providing mattress support.

5. Usage Guidelines

To ensure safe and effective use of your Bellemave L-Shaped Bunk Bed, please observe the following guidelines:

• Mattress Placement: Place a standard Twin size mattress on the upper bunk and loft bed, and a standard Full size mattress on the lower bunk. No box spring is required as the bed is designed with supportive wooden slats.
• Staircase Use: Use the integrated staircase for safe access to the upper bunk and loft bed. The stairs also provide convenient storage compartments.
• Drawer Functionality: The three under-bed drawers offer additional storage space. Ensure they slide smoothly and are not overloaded.
• Weight Distribution: Distribute weight evenly across the bed surfaces. Avoid concentrating heavy loads in one area.
• Prohibited Activities: Do not allow jumping on the beds, rough play, or hanging from any part of the bed structure.

Figure 5.1: The storage stairs providing access to the upper bunk and additional storage.

6. Maintenance

Regular maintenance will help preserve the appearance and structural integrity of your bunk bed.

• Cleaning: Wipe surfaces with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners that may damage the finish.
• Hardware Check: Periodically inspect all bolts, screws, and connections. Retighten any loose hardware to maintain stability and safety.
• Drawer Slides: Ensure drawer slides are clean and free of obstructions for smooth operation.
• Wood Care: Protect the wood finish from direct sunlight and extreme temperature changes to prevent warping or fading.

7. Troubleshooting

8. Product Specifications

• Brand: Bellemave
• Model: L Shaped Bunk Bed with Storage Stairs and 3 Drawers
• ASIN: B0BVB4T33D
• Color: Espresso
• Material: Solid Pine Wood
• Overall Dimensions (L x W x H): 118.3" x 96.8" x 61.2"
• Compatible Mattress Size: Twin (upper bunk, loft bed), Full (lower bunk)
• Assembly Required: Yes
• Special Feature: Durable construction, integrated storage stairs, 3 under-bed drawers, no box spring needed.

Figure 8.1: Side view of the L-shaped bunk bed, highlighting the loft bed and storage stairs.

9. Warranty and Customer Support

For any questions regarding assembly, missing parts, or product issues, please contact Bellemave customer service. Refer to your purchase documentation for specific warranty details and contact information.

Please have your model number (B0BVB4T33D) and purchase date available when contacting support.