Elitech Tlog 10E Digital Temperature Data Logger User Manual

1. Introduction

This manual provides detailed instructions for the proper use, setup, operation, and maintenance of your Elitech Tlog 10E Digital Temperature Data Logger. Please read this manual thoroughly before using the device to ensure optimal performance and accurate data collection.

The Elitech Tlog 10E is a reusable temperature recorder designed for various applications, including life science, food cold chain, and industrial fields. It features automatic PDF report generation, a USB interface, and a 32,000-point memory capacity.

2. Product Overview

2.1 Key Features

• Automatic PDF Report: Generates PDF reports with embedded data directly, requiring no special software for basic data access.
• Data Visualization: LCD screen displays current temperature, maximum/minimum values, date, and record points. Supports Fahrenheit/Celsius switching.
• Anti-touch Button Design: Prevents accidental button presses during transport or handling.
• Parameter Settable: Customizable temperature unit, alarm range, and logging interval via Elitechlog software.
• High Memory Capacity: Stores up to 32,000 data points.
• External Temperature Probe: For precise temperature measurement in various environments.
• IP65 Waterproof: Provides protection against dust and water splashes.
• FDA 21 CFR Part 11 Compliant: Meets regulatory standards for electronic records.

2.2 Package Contents

• Elitech Tlog 10E Digital Temperature Data Logger
• External Temperature Probe
• User Manual (this document)

2.3 Device Components

• External Sensor: Connects to the main unit for temperature measurement.
• LED Indicator: Provides status updates (e.g., recording, alarm).
• Buttons (START/STOP): Used to initiate and terminate data logging, and for status checks.
• USB Port: Located at the bottom, used for connecting to a computer for data download and configuration.

3. Setup

3.1 Initial Preparation

1. Unpack: Carefully remove the data logger and its accessories from the packaging.
2. Connect External Probe: Insert the external temperature probe connector firmly into the designated port on the data logger.
3. Power On: The device is battery-powered. Ensure the battery is installed and has sufficient charge. The LCD will activate upon initial use or button press.

3.2 Software Installation (Optional for Advanced Configuration)

While the device can generate basic PDF reports without software, advanced configuration (e.g., setting alarm ranges, logging intervals, temperature unit) requires the Elitechlog software. This software can typically be downloaded from the official Elitech website.

1. Download Software: Visit the Elitech official website and download the Elitechlog software compatible with your operating system.
2. Install: Follow the on-screen instructions to install the software on your computer.
3. Connect Device: Once installed, connect the Tlog 10E to your computer's USB port. The software should detect the device.

4. Operating Instructions

4.1 Starting a Recording

1. Ensure the external probe is securely connected.
2. Press and hold the START button for approximately 3 seconds until the "REC" indicator appears on the LCD, confirming that recording has begun.
3. The device will now log temperature data at the pre-set interval.

4.2 Stopping a Recording

1. Press and hold the STOP button for approximately 3 seconds until the "REC" indicator disappears from the LCD.
2. The recording session is now complete, and the data is saved in the device's memory.

Note: The anti-touch button design helps prevent accidental starts or stops. Ensure a firm and sustained press when operating the buttons.

4.3 Viewing Data on LCD

The LCD screen provides real-time temperature readings and other status information. Briefly press the START button to cycle through display modes, which may include current temperature, maximum temperature, minimum temperature, recording points, and current time.

4.4 Switching Temperature Units (°C/°F)

To switch between Celsius (°C) and Fahrenheit (°F) units, connect the device to a computer and use the Elitechlog software. Navigate to the settings menu within the software to adjust the temperature unit preference.

5. Data Management

5.1 Automatic PDF Report Generation

After stopping a recording session, connect the Tlog 10E to a computer's USB port. The device will automatically generate a PDF report containing the recorded temperature data. This report can be accessed directly as a removable drive, similar to a USB flash drive.

5.2 Using Elitechlog Software for Advanced Analysis

For more detailed analysis, parameter configuration, and data export options (e.g., Excel, ELT, text files), use the Elitechlog software. Connect the data logger to your computer, open the software, and follow the prompts to download and analyze the recorded data.

6. Maintenance

6.1 Cleaning

Wipe the device clean with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the casing or electronic components. Ensure the USB port cover is closed when not in use to maintain IP65 rating.

6.2 Battery Replacement

The Tlog 10E is powered by a replaceable battery. When the battery indicator on the LCD shows low power, replace the battery with a new one of the same type. Refer to the device's specifications for the correct battery type. Ensure proper polarity during installation.

6.3 Storage

Store the data logger in a cool, dry place away from direct sunlight and extreme temperatures when not in use. If storing for extended periods, it is recommended to remove the battery to prevent leakage.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Elitech website or contact Elitech customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

Official Elitech Website: www.elitechlog.com