STAPLES Emerge Vortex Bonded Leather Gaming Chair

Introduction

Thank you for choosing the STAPLES Emerge Vortex Bonded Leather Gaming Chair. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure you get the most out of your new chair. Please read this manual thoroughly before assembly and use, and retain it for future reference.

Important Safety Information

• Ensure all parts are present and undamaged before assembly. Do not use if any parts are missing or broken.
• Follow assembly instructions carefully. Improper assembly can lead to instability and injury.
• Do not stand on the chair. Use it only for seating one person at a time.
• Do not use the chair if any components are loose or damaged. Tighten all screws periodically.
• Keep children away from the assembly area. Small parts may be a choking hazard.
• This chair is designed to support up to 275 lbs. Do not exceed this weight limit.

Parts List

Please verify that all components listed below are included in your package before beginning assembly.

• A. Backrest
• B. Seat Cushion
• C. Armrests (2)
• D. Star Base
• E. Casters (5)
• F. Gas Lift Cylinder
• G. Seat Mechanism
• H. Screw Kit (various screws, washers, Allen wrench)

Overall view of the STAPLES Emerge Vortex Gaming Chair, showcasing its black and blue bonded leather design.

Assembly Instructions

Follow these steps carefully to assemble your gaming chair.

1. Attach Casters to Base: Insert each of the five casters (E) into the holes at the end of each leg of the star base (D) until they click securely into place. Ensure they are fully seated.
   

   The durable five-star base with wear-resistant 360-degree casters, designed for stability and smooth movement.

2. Insert Gas Lift: Place the gas lift cylinder (F) into the center hole of the assembled star base (D).
3. Attach Seat Mechanism: Align the seat mechanism (G) with the pre-drilled holes on the underside of the seat cushion (B). Ensure the front of the mechanism faces the front of the seat. Secure it with the appropriate screws from the screw kit (H), tightening them firmly with the Allen wrench.
4. Attach Armrests: Attach the armrests (C) to the sides of the seat cushion (B) using the designated screws from the screw kit (H). Ensure they are oriented correctly (left and right armrests).
5. Connect Backrest to Seat: Align the metal plates on the backrest (A) with the corresponding holes on the sides of the seat cushion (B) and armrests (C). Secure with screws from the screw kit (H).
6. Assemble Chair onto Gas Lift: Carefully place the assembled seat, backrest, and armrest unit onto the gas lift cylinder (F) that is already inserted into the star base. Press down firmly to secure.

Operating Instructions

Your STAPLES Emerge Vortex Gaming Chair offers several adjustable features for personalized comfort.

• Seat Height Adjustment: To raise the seat, lift the lever located on the right side of the chair while taking your weight off the seat. To lower the seat, lift the same lever while seated. Release the lever to lock the height.
  

  The chair's seat height can be adjusted by lifting the lever on the right side.

• Recline and Tilt Lock: To recline the backrest, pull the lever on the left side of the chair. Lean back to your desired angle and release the lever to lock the position. The chair supports a recline range of 90 to 120 degrees.
• Tilt Tension Adjustment: The knob located underneath the seat, at the front of the mechanism, controls the tilt tension. Turn clockwise to increase tension (making it harder to recline) or counter-clockwise to decrease tension (making it easier to recline).
  

  The chair offers a recline range of 90 to 120 degrees and a full 360-degree swivel for versatile movement.

• Flip-Up Armrests: The armrests can be flipped up to allow for easier positioning under a desk or for more freedom of movement. Simply lift the armrests upwards until they lock into the upright position. To lower, gently pull them down.
• 360-Degree Swivel: The chair is designed to swivel 360 degrees, providing full rotational movement.
• Lumbar Support and Headrest: The chair features a built-in padded headrest and lumbar support for enhanced comfort during extended use.
  

  Close-up view of the chair emphasizing the built-in padded headrest and lumbar support for ergonomic comfort.

Care and Maintenance

Proper care will extend the life and appearance of your chair.

• Cleaning: For bonded leather surfaces, wipe with a soft, damp cloth. For tougher spots, use a mild soap solution and wipe dry immediately. Avoid harsh chemicals or abrasive cleaners.
• Inspection: Periodically check all screws and bolts to ensure they are tight. Re-tighten as necessary to maintain stability and safety.
• Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause the bonded leather to fade or crack.
• Weight Limit: Do not exceed the maximum weight capacity of 275 lbs.

Detail showing the bonded leather material with color-contrast stitching and the thick foam padding for comfort.

Troubleshooting

If you encounter any issues with your chair, refer to the common problems and solutions below.

Product Specifications

Key dimensions and specifications for the STAPLES Emerge Vortex Gaming Chair.

Visual representation of the chair's key dimensions, including height, width, depth, and seat measurements.

Warranty and Customer Support

Your STAPLES Emerge Vortex Bonded Leather Gaming Chair is backed by a 7-year manufacturer limited warranty. This warranty covers defects in materials and workmanship under normal use.

For warranty claims, missing parts, or any other product-related inquiries, please contact STAPLES customer support. Refer to your purchase receipt or the STAPLES official website for the most current contact information.

When contacting support, please have your model number (58293-CCVS) and proof of purchase readily available.