Ancona 36" 440 CFM Ducted Under Cabinet Range Hood User Manual

1. Introduction

This manual provides essential information for the safe installation, operation, and maintenance of your Ancona 36" 440 CFM Ducted Under Cabinet Range Hood. Please read this manual thoroughly before installation and use, and retain it for future reference.

The Ancona AN-18043BLK range hood is designed to effectively remove smoke, grease, moisture, and odors from your kitchen, ensuring a clean and fresh cooking environment. It features a powerful 440 CFM motor, 3-speed electronic controls, and long-lasting LED lighting.

2. Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, or injury to persons.

• Read all instructions before installation and operation.
• Installation must be performed by a qualified technician in accordance with all applicable codes and standards.
• Ensure the power supply is disconnected before servicing or cleaning.
• This range hood is for general ventilating use only. Do not use to exhaust hazardous or explosive materials.
• Maintain proper ventilation in the room when the range hood is used simultaneously with appliances burning gas or other fuels.
• Clean grease filters regularly to prevent grease fires.
• Do not flambé under the range hood.
• Ensure ductwork is properly sized and sealed.

3. Package Contents

Verify that all components are present and undamaged upon unpacking.

• Main Range Hood Unit
• Damper Flap
• Baffle Filters (Quantity: 3 for 36" model)
• Mounting Screws and Hardware
• User Manual

Figure 3.1: Front view of the Ancona 36" Under Cabinet Range Hood. This image shows the overall design of the range hood, including the black finish and the stainless steel baffle filters visible from below.

4. Setup and Installation

This range hood is designed for under-cabinet mounting with top venting (round 6 inch duct). Ensure adequate clearance and structural support before installation.

4.1 Pre-Installation Checklist

• Verify the required electrical supply (120V).
• Confirm ducting requirements (6-inch round duct, external ventilation only).
• Ensure cabinet strength to support the unit's weight (approx. 24.2 lbs).
• Measure and mark the installation area for precise placement.

4.2 Mounting the Range Hood

1. Locate and mark the center of the cabinet where the hood will be installed.
2. Drill pilot holes for mounting screws according to the template (if provided) or measurements.
3. Secure the range hood to the underside of the cabinet using the provided mounting screws. Ensure it is level and securely fastened.
4. Connect the 6-inch round ductwork to the top exhaust outlet of the range hood. Ensure all connections are sealed to prevent air leaks.

Figure 4.1: Dimensional view of the Ancona Range Hood. This image illustrates the key measurements: 35.4" (90 cm) width, 20.5" (52 cm) depth, and 9.75" (24.8 cm) height, crucial for installation planning.

Figure 4.2: Top view of the range hood, highlighting the circular duct connection point. This view is important for understanding the ventilation setup.

5. Operating Instructions

The range hood features a 3-speed electronic control panel with touch controls for fan speed and lighting.

5.1 Control Panel Overview

Figure 5.1: Close-up of the electronic touch control panel. This image shows the various buttons for fan speed adjustment, light control, and the time-delay auto shut-off feature.

5.2 Fan Operation

• Power Button: Press to turn the fan on or off.
• Speed Control Buttons: Use the '+' and '-' buttons to cycle through the 3 fan speeds (Low, Medium, High).
• Time-Delay Auto Shut-Off: Activate this feature to allow the fan to run for a set period before automatically turning off. Refer to the control panel for specific timing options.

5.3 Lighting Operation

Figure 5.2: Detail of the integrated LED lights. These lights provide illumination for the cooking surface and are energy-efficient.

• Light Button: Press to turn the LED lights on or off.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your range hood.

6.1 Cleaning Baffle Filters

The stainless steel baffle filters are designed to trap grease and are dishwasher safe for easy cleaning.

Figure 6.1: Detail of the stainless steel baffle filters. These filters are removable for cleaning and are designed to efficiently capture grease.

1. Turn off the range hood and disconnect power.
2. Remove the baffle filters by pulling the release latch and sliding them out.
3. Wash filters in a dishwasher or by hand using hot water and a non-abrasive detergent.
4. Allow filters to dry completely before re-installing.

6.2 Cleaning Exterior Surfaces

• Wipe the exterior surfaces with a soft cloth dampened with mild soap and water.
• Do not use abrasive cleaners, steel wool, or scouring pads, as these can damage the finish.
• Dry thoroughly with a clean, soft cloth.

7. Troubleshooting

Refer to this section for common issues and their solutions. If the problem persists, contact customer support.

8. Specifications

9. Warranty and Support

This product is covered by a manufacturer's warranty. For specific warranty details, please refer to the warranty card included with your product or visit the Ancona website.

For technical assistance, troubleshooting not covered in this manual, or to order replacement parts, please contact Ancona Customer Service. Keep your model number (AN-18043BLK) and purchase date ready when contacting support.

Return Policy: Products purchased from Amazon.com typically have a 30-day return policy from the date of purchase. Please refer to Amazon's return policy for the most current information.