1. Introduction
Thank you for purchasing the GLIDiC TW-3000F Wireless Earbuds. This manual provides essential information for the safe and effective use of your device. Please read it thoroughly before use and retain it for future reference.
2. Package Contents
Verify that all items are present in your package:
- Earbuds (Left/Right) x 1 pair
- Eartips (S/M/L) x 2 sets (one set pre-installed)
- Charging Case x 1
- Charging Cable x 1
- Quick Guide / Warranty Card x 1
Image: The GLIDiC TW-3000F wireless earbuds (coral pink) and their matching charging case.
3. Product Overview
The GLIDiC TW-3000F earbuds are designed for comfort and functionality, featuring Active Noise Cancelling (ANC), ambient sound capture, and a low latency mode.
Image: A GLIDiC TW-3000F earbud comfortably seated in a user's ear, demonstrating its ergonomic design.
4. Setup
4.1. Charging the Earbuds and Case
Before first use, fully charge the earbuds and charging case.
- Place the earbuds into the charging case. Ensure they are correctly seated.
- Connect the charging cable to the charging case's port and a USB power source.
- The indicator lights on the case will show the charging status.
A 10-minute quick charge provides approximately 1 hour and 45 minutes of playback.
4.2. Pairing with a Device
- Open the charging case. The earbuds will automatically enter pairing mode.
- On your device (smartphone, tablet, etc.), enable Bluetooth.
- Search for available Bluetooth devices and select "GLIDiC TW-3000F".
- Once connected, a confirmation sound will play, and the indicator light on the earbuds will change.
5. Operating Instructions
The GLIDiC TW-3000F features intuitive touch controls on each earbud.
5.1. Power On/Off
- Power On: Open the charging case, or press and hold the touch sensor on both earbuds for 3 seconds.
- Power Off: Place the earbuds back into the charging case and close the lid, or press and hold the touch sensor on both earbuds for 5 seconds.
5.2. Music Playback
- Play/Pause: Single tap on either earbud.
- Next Track: Double tap the right earbud.
- Previous Track: Double tap the left earbud.
- Volume Up: Triple tap the right earbud.
- Volume Down: Triple tap the left earbud.
5.3. Call Management
- Answer/End Call: Single tap on either earbud.
- Reject Call: Press and hold the touch sensor on either earbud for 2 seconds.
5.4. Active Noise Cancelling (ANC) and Ambient Sound Mode
These modes allow you to control your listening environment.
- Switch Modes: Press and hold the touch sensor on the left earbud for 2 seconds to cycle through ANC On, Ambient Sound On, and ANC Off.
Image: A GLIDiC TW-3000F earbud with visual representations of sound waves, illustrating its noise-cancelling capabilities.
5.5. Low Latency Mode
Reduce audio delay for gaming or video playback.
- Activate/Deactivate: Quadruple tap the right earbud.
Image: GLIDiC TW-3000F earbuds next to a smartphone displaying a video, highlighting the low latency feature for synchronized audio and visuals.
6. Maintenance
6.1. Cleaning
- Gently wipe the earbuds and charging case with a soft, dry cloth.
- Remove eartips and clean them with mild soap and water if necessary. Ensure they are completely dry before reattaching.
- Do not use abrasive cleaners or solvents.
6.2. Storage
- Store the earbuds in their charging case when not in use to protect them and keep them charged.
- Avoid storing in extreme temperatures or high humidity.
6.3. Water Resistance (IPX4)
The earbuds are rated IPX4, meaning they are resistant to splashing water from any direction. They are not designed for submersion in water.
Image: An umbrella with raindrops, symbolizing the IPX4 water resistance of the earbuds, suitable for use in light rain or during workouts.
7. Troubleshooting
| Problem | Possible Solution |
|---|---|
| Earbuds do not power on. | Ensure earbuds are charged. Place them in the charging case and connect the case to power. |
| Cannot pair with device. | Ensure Bluetooth is enabled on your device. Place earbuds in case, close, then open to re-enter pairing mode. Forget the device on your phone and try pairing again. |
| No sound or low volume. | Check device volume. Ensure earbuds are properly seated in your ears. Clean any debris from the earbud nozzles. |
| ANC/Ambient mode not working. | Ensure the earbuds are properly worn. Cycle through the modes by pressing and holding the left earbud's touch sensor. |
| Earbuds disconnect frequently. | Ensure your device is within Bluetooth range. Avoid obstacles between earbuds and device. |
8. Specifications
- Model: TW-3000F
- Connectivity: Bluetooth 5.2
- Features: Active Noise Cancelling (ANC), Ambient Sound Mode, Low Latency Mode, IPX4 Water Resistance, Quick Charge
- Continuous Playback: Approximately 6.5 hours (earbuds)
- Battery Type: Earbuds: Lithium-ion, Charging Case: Lithium-polymer
- Earbud Dimensions (approx.): 18mm (W) x 20mm (D) x 32mm (H)
- Product Weight: 100g
- Included Components: Earbuds (L/R) x1, Eartips (S/M/L) x2, Charging Case x1, Charging Cable x1, Quick Guide/Warranty x1
9. Safety Information
Please observe the following safety precautions:
- Do not disassemble, repair, or modify the device.
- Keep away from extreme temperatures, direct sunlight, and high humidity.
- Avoid dropping or subjecting the device to strong impacts.
- Keep out of reach of children and pets.
- Do not use while driving or in situations where inability to hear ambient sounds could be dangerous.
10. Warranty and Support
The GLIDiC TW-3000F Wireless Earbuds come with a 1-year manufacturer's warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
For technical support or warranty inquiries, please contact GLIDiC customer service:
- Online Support: Visit the official GLIDiC website for a 24-hour chatbot service.
- Phone/Email Support: Available from 10:00 to 19:00 (excluding specific holidays). Refer to your quick guide or the official website for contact details.
