Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your OPT7 Aura DreamColor Underglow Chasing Light Kit. This kit features RGB-IC LED strips with advanced multicolor displays, controllable via a remote and the OPT7 GLOW APP. It is designed for universal fitment on various vehicles and is built for durability.
What's Included
Verify that all components listed below are present in your package:
- 1 x Aura DreamColor Control Box
- 1 x E-Z Handheld Remote
- 1 x Inline Fuse Power Wire
- 2 x 36-inch RGBIC LED Strips with Extension Wire (2ft rear, 8ft front)
- 2 x 48-inch RGBIC LED Strips with Extension Wire (9ft left/right)
- 1 x Pack of Mounting Kit (brackets, screws)
- Zip Ties
Setup and Installation
Follow these steps for a safe and effective installation of your underglow kit.
1. Planning and Placement
Before permanent installation, plan the layout of the LED strips under your vehicle. Ensure strips are placed where they will not be damaged by road debris or moving parts. The kit includes two 36-inch strips (for front/rear) and two 48-inch strips (for sides).
2. Mounting the LED Strips
- Clean the mounting surfaces thoroughly to ensure proper adhesion.
- Apply the strong binding tapes to the back of the LED strips.
- Secure the LED strips using the provided mounting brackets and screws. For additional security, use zip ties where appropriate.
3. Connecting Components
Connect the LED strips to the Aura DreamColor Control Box. Ensure all connections are secure and waterproof. Pay close attention to the arrows on the connectors to ensure correct alignment.
Important: This kit is only compatible with DreamColor RGBIC control boxes and is not compatible with Aura 4-Pin LED lighting connections.
4. Power Connection
The kit includes an inline fuse power battery harness for direct and safe battery connection. Connect the power wire to your vehicle's 12V battery. Ensure all wiring is routed safely away from hot or moving parts and secured with zip ties.
For optional fuse tap installation, consider purchasing the OPT7 Aura Universal Fuse Tap Adapter Set (B0B7QVF6B9).
Operating Instructions
Your OPT7 Aura DreamColor kit can be controlled via the included E-Z Remote or the OPT7 GLOW APP.
1. Using the E-Z Remote
The remote allows for basic control of colors, brightness, and dynamic effects.
Pairing the Remote:
To pair the remote, reconnect the power to the control box, then aim the remote at the device and hold the 'ON' button until the LED strips flash white.
2. Using the OPT7 GLOW APP
The OPT7 GLOW APP provides advanced control features, including unlimited colors, brightness dimmer options, dynamic effects, and music-activated lighting.
App Features:
- Versatile Illumination Options: Choose from a wide range of lighting effects.
- Unlimited Color Choices: Select any color from the color wheel.
- Music Rhythm Modes: Sync lights to music via phone mic (Android Auto supported) or imported music files.
- Light Effect Animations: Unleash various animated light patterns.
- Custom Light Modes: Create and save personalized lighting settings.
- Multi-Kit Sync: Sync up to 4 kits for a coordinated light show.
Maintenance
The OPT7 Aura DreamColor kit is designed to be durable and water-resistant (IP67 rated). To ensure longevity:
- Regularly inspect wiring and connections for any signs of wear or damage.
- Ensure all waterproof connections are properly sealed after any adjustments.
- Clean the LED strips periodically with a damp cloth to remove dirt and grime, avoiding harsh chemicals.
- Avoid high-pressure washing directly on the LED strips or control box.
Troubleshooting
If you encounter issues with your OPT7 Aura DreamColor kit, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn on. | No power, loose connection, blown fuse. | Check battery connection. Ensure all connectors are securely fastened. Inspect the inline fuse and replace if blown. |
| Lights are not displaying correct colors or patterns. | Incorrect app settings, remote not paired, damaged LED strip. | Verify settings in the OPT7 GLOW APP. Re-pair the remote control (see Operating Instructions). Inspect LED strips for physical damage. |
| Remote control is unresponsive. | Remote battery low, remote not paired. | Replace remote battery. Re-pair the remote control. |
| App cannot connect to the control box. | Bluetooth issue, control box not powered. | Ensure Bluetooth is enabled on your device. Restart the app and control box. Verify control box has power. |
| Part of an LED strip is not lighting up. | Damaged section of the strip, loose connection. | Inspect the specific section for damage. Check connections to that strip. |
Specifications
- Model: AURA-GLOW-UNDERGLOW-ARGB-FLEX-KIT
- LED Type: 5050 RGB-IC LEDs
- Control: APP & Remote Control
- Voltage: 12V
- Water Resistance: IP67 Waterproof
- Material: Silicone
- Included Strips: 2 x 36-inch, 2 x 48-inch
- Special Features: Breath Effect, Color Chasing, Extendable
- Item Weight: 1.8 Pounds
- Product Dimensions: 10 x 9.8 x 5 inches (packaging)
- Automotive Fit Type: Universal Fit
Warranty Information
The OPT7 Aura DreamColor Underglow Chasing Light Kit comes with an industry-leading 1-Year Warranty. This warranty covers manufacturing defects and ensures product reliability. For warranty claims or assistance, please contact OPT7 customer support.
Customer Support
For further assistance, technical support, or warranty inquiries, please visit the official OPT7 website or contact their customer service team. Details can typically be found on the product packaging or the OPT7 brand store on Amazon.
OPT7 Brand Store: Visit the OPT7 Store on Amazon
