1. Introduction
This manual provides essential information for the installation, maintenance, and troubleshooting of the original Teka dishwasher door latch replacement part. This component is crucial for the proper and safe operation of your dishwasher, ensuring the door remains securely closed during cycles. Please read these instructions carefully before proceeding with any installation or maintenance.
2. Product Overview
The product is an original replacement door latch mechanism for specific Teka dishwasher models. It is designed to restore the secure closing function of your dishwasher door, which is vital for preventing leaks and ensuring efficient operation. The latch assembly typically consists of a plastic housing, a spring mechanism, and a hook or catch that engages with the dishwasher frame.
Figure 1: Image of the Teka dishwasher door latch replacement part. This component is a beige-colored plastic assembly featuring an internal metal spring and hook mechanism, designed to secure the dishwasher door during operation.
3. Compatibility
This original replacement door latch (Original Code: 81782909, Manufacturer Reference: 218780027) is compatible with the following Teka dishwasher models:
- LP7 840 BLANC
- LP7 400 BLANC
- LP7 811 INOX
- MLP 800 INOX
Always verify your dishwasher's model number and the original part number to ensure correct compatibility before purchasing and installing this replacement part.
4. Safety Information
Before attempting any repair or replacement, observe the following safety precautions:
- Disconnect Power: Always unplug the dishwasher from the electrical outlet or turn off the circuit breaker before beginning any work.
- Water Supply: Turn off the water supply to the dishwasher.
- Personal Protective Equipment: Wear appropriate safety gear, such as gloves, to protect your hands.
- Professional Assistance: If you are unsure about any step or lack the necessary tools/experience, it is recommended to consult a qualified appliance technician.
5. Installation Instructions
The following steps provide a general guide for replacing a dishwasher door latch. Specific procedures may vary slightly depending on your exact dishwasher model. Refer to your dishwasher's service manual for detailed instructions if available.
- Prepare the Dishwasher: Ensure the dishwasher is disconnected from power and water supply. Open the dishwasher door.
- Access the Latch: The door latch is typically located at the top center of the dishwasher door. You may need to remove the inner door panel to access the latch mechanism. This usually involves removing screws around the perimeter of the inner door panel.
- Disconnect Wiring: Carefully disconnect any electrical wires connected to the old latch mechanism. Note their positions or take a photo for reassembly.
- Remove Old Latch: Unscrew and remove the old door latch assembly from its mounting.
- Install New Latch: Position the new replacement latch in the same location as the old one. Secure it with the screws.
- Reconnect Wiring: Reconnect the electrical wires to the new latch, ensuring they are securely attached.
- Reassemble Door: Reattach the inner door panel, ensuring all screws are tightened properly.
- Test Operation: Close the dishwasher door to ensure the new latch engages correctly. Reconnect power and water, then run a short test cycle to check for proper door closure and absence of leaks.
6. Maintenance
To ensure the longevity and proper function of your dishwasher door latch, consider the following maintenance tips:
- Regular Cleaning: Periodically inspect the latch area for food debris or residue. Clean with a damp cloth and mild detergent if necessary.
- Avoid Force: Do not force the dishwasher door open or closed. If it's sticking, investigate the cause rather than applying excessive force, which can damage the latch.
- Inspect for Wear: Occasionally check the latch mechanism for signs of wear, cracks, or loose components. Address any issues promptly.
7. Troubleshooting
If you experience issues with your dishwasher door latch, consult the table below for common problems and potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Door does not latch securely | Misalignment, worn latch, or obstruction | Check for obstructions. Inspect latch for damage. Adjust door alignment if possible. Replace latch if worn. |
| Dishwasher does not start | Door not fully closed/latched (safety switch) | Ensure door is firmly closed until the latch engages. Inspect latch switch for proper function. |
| Door opens during cycle | Faulty latch mechanism | The latch is likely failing and requires replacement. |
8. Specifications
| Specification | Detail |
|---|---|
| Product Type | Dishwasher Door Latch Replacement Part |
| Brand (Dishwasher) | Teka |
| Original Code | 81782909 |
| Manufacturer Reference | 218780027 |
| Compatible Models | LP7 840 BLANC, LP7 400 BLANC, LP7 811 INOX, MLP 800 INOX |
| Manufacturer (Part Supplier) | ALL4SALE |
9. Warranty and Support
Information regarding specific warranty terms for this replacement part is not provided in the product details. For warranty claims or technical support, please contact the seller, ALL4SALE, or refer to the documentation that accompanied your original purchase. Availability of spare parts information is also not explicitly stated, but as this is a replacement part, it is generally available through the supplier.
