Introduction
This manual provides detailed instructions for the installation and care of your Lamshaw TPU Screen Protector, designed specifically for the MorePro FT26 Smart Watch and FITVII FT26 Fitness Tracker. Please read these instructions carefully before installation to ensure optimal performance and protection for your device.
The screen protector is made from Thermoplastic Polyurethane (TPU), offering full coverage, high transparency, and sensitivity while providing anti-shatter and anti-scratch properties.
Package Contents
Your package includes:
- Lamshaw TPU Screen Protectors (6 Pack)
- Installation accessories (wet wipes, dry wipes, fiber cloth, installation card)
Image: The Lamshaw screen protector packaging shown alongside a compatible MorePro FT26 Smart Watch, illustrating the product's intended use.
Installation Instructions
Follow these steps carefully for a bubble-free installation:
- Clean the Screen: Use the provided wet wipe to thoroughly clean your watch screen. Follow with the dry wipe to remove any moisture. Finally, use the fiber cloth to remove any remaining dust or lint.
- Identify Layers: The protector has three layers. The middle layer is the actual screen protector. It is sandwiched between a red "Back 1" layer and a black "Front 2" layer. The side of the middle layer that adheres to the screen is stickier to the "Back 1" side.
- Remove Back Layer: Carefully peel off the Red "Back 1" layer.
- Align and Apply: Align the exposed sticky side of the protector with one edge of your watch screen. Slowly lower the protector onto the screen.
- Smooth Out: Using the provided installation card, gently push from the applied edge towards the opposite side to smooth out the protector and remove air bubbles.
- Remove Front Layer: Once the protector is smoothly applied, carefully peel off the Black "Front 2" layer.
- Final Smoothing: If any small bubbles remain, use the card to gently push them towards the edges until they disappear. For larger bubbles, you may need to carefully lift a corner of the protector and reapply, smoothing it out again.
Important Note: If you accidentally peel off the "Front 2" layer first and find the exposed side is not sticky, it means you've exposed the wrong side. In this case, gently wrinkle the Red "Back 1" layer to separate it from the middle layer. Peel off the middle layer, then re-align it with the Black "Front 2" layer, ensuring the correct sticky side is exposed for application.
Image: A visual guide demonstrating the six steps for applying the screen protector to a smartwatch, from cleaning to final smoothing.
Image: A diagram illustrating the three distinct layers of the screen protector: two plastic films (top and bottom) and the central TPU screen protector layer.
Usage and Performance
Once properly installed, your Lamshaw TPU Screen Protector will provide continuous protection for your MorePro FT26 or FITVII FT26 Smart Watch screen. It is designed to maintain high transparency and touch sensitivity, ensuring your watch's display and functionality are unaffected.
The TPU material offers:
- Scratch Resistance: Protects against daily wear and minor abrasions.
- Anti-Shatter: Adds a layer of protection against impacts.
- High Transparency: Ensures clear viewing of your watch display.
- High Sensitivity: Maintains original touch response.
Image: A close-up of the screen protector being flexed around a pen tip, highlighting its soft, flexible, and durable TPU material.
Care and Maintenance
To keep your screen protector in optimal condition:
- Cleaning: Gently wipe the screen protector with a soft, lint-free cloth. For smudges, a slightly damp cloth (water only) can be used, followed by a dry cloth. Avoid harsh chemicals or abrasive materials.
- Avoid Sharp Objects: While the protector is scratch-resistant, extreme pressure or very sharp objects can still damage it.
- Replacement: If the protector becomes heavily scratched or damaged, replace it with a new one from the pack to maintain optimal screen clarity and protection.
Troubleshooting
Bubbles After Installation
- Small Bubbles: Many small bubbles will self-heal over 24-48 hours. For persistent small bubbles, gently push them towards the nearest edge using the installation card.
- Large Bubbles: If a large bubble remains, it may indicate dust or improper application. Carefully lift the nearest edge of the protector, clean the area with a dust sticker (if available, or a piece of tape), and reapply, smoothing with the card.
- Edge Lifting: Ensure the edges are firmly pressed down during installation. If an edge lifts, gently press it back down with your finger or the card.
Incorrect Layer Removal
- If you accidentally peel off the "Front 2" layer first and the exposed side is not sticky, refer to step 2 and the "Important Note" in the Installation Instructions section for guidance on how to correctly separate the layers and reapply.
Product Specifications
| Brand | Lamshaw |
| Compatible Devices | MorePro FT26 Smart Watch, FITVII FT26 Fitness Tracker |
| Material | Thermoplastic Polyurethane (TPU) |
| Special Features | Scratch Resistant, Anti-Shatter, High Transparency, High Sensitivity |
| Finish Type | Glossy |
| Number of Items | 6 (in a pack) |
Warranty and Support
Information regarding specific warranty terms or direct customer support contacts for this product is not available in the provided documentation. For any issues or inquiries, please refer to the retailer or the original product packaging for contact details.