PATPET Dog Training Collar Receiver P Collar 680 User Manual

Introduction

This manual provides comprehensive instructions for the safe and effective use of your PATPET Dog Training Collar Receiver, model P Collar 680. This device is designed to assist in dog training through various modes, ensuring a humane and effective experience for both pet and owner. Please read this manual thoroughly before use.

Image: The PATPET Dog Training Collar Receiver P Collar 680. This image displays the black receiver unit attached to a black and white patterned collar strap, with the PATPET logo visible on the receiver.

Key Features

• 3 Training Modes: Offers adjustable shock (levels 1-16), vibration, and tone modes for varied training needs.
• IPX7 Waterproof: Designed to withstand immersion in water, allowing use in various weather conditions and environments.
• Rechargeable Receiver: Features a USB interface for convenient charging via PC, laptop, power bank, or power adapter.
• Security Switch & Conductive Silicone: Includes a safety switch to prevent accidental activation and conductive silicone covers for pet comfort and skin protection.
• 2 Channels Maximum Control: Capable of pairing with two receivers simultaneously, allowing one remote to control two dogs.

Setup Guide

1. Charging the Receiver

1. Locate the charging port on the receiver.
2. Connect the USB charging cable to the receiver and a compatible USB power source (e.g., computer, power adapter).
3. The indicator light on the receiver will typically show charging status (e.g., red for charging, green for fully charged).
4. Allow approximately 2-3 hours for a full charge.

2. Attaching the Collar Strap

• Thread the collar strap through the loops on the receiver unit.
• Ensure the receiver is positioned centrally on the strap.

3. Fitting the Collar on Your Dog

• Place the receiver on your dog's neck, ensuring the contact points are positioned underneath, making direct contact with the skin.
• Adjust the strap for a snug fit. You should be able to fit one or two fingers comfortably between the collar strap and your dog's neck.
• Avoid overtightening, as this can cause discomfort or skin irritation. A loose collar will prevent effective contact.

4. Pairing with a Remote Transmitter

This receiver is designed to be paired with a compatible PATPET remote transmitter (sold separately). Refer to your remote transmitter's manual for specific pairing instructions. Generally, the process involves:

1. Turn on the receiver.
2. Activate pairing mode on the receiver (often by holding a button).
3. Initiate pairing on the remote transmitter.
4. Confirm successful pairing via indicator lights on both devices.
5. For multi-dog training, repeat the pairing process for additional receivers on different channels of your remote.

Operating Instructions

The PATPET P Collar 680 receiver responds to commands from a paired remote transmitter. Ensure your remote is charged and paired correctly before use.

Training Modes

• Tone Mode: Delivers an audible beep. This is often used as an initial warning or for positive reinforcement.
• Vibration Mode: Provides a tactile vibration. This can be used as a stronger warning or a primary training cue.
• Adjustable Shock Mode: Delivers a static stimulation. The intensity can be adjusted from level 1 to 16 on your remote transmitter. Always start at the lowest level and increase gradually if necessary, observing your dog's reaction.

Using the Security Switch

The receiver features a security switch, typically located on the unit, to prevent unintended activation. Ensure this switch is in the "ON" position during training and "OFF" when not in use or when charging to conserve battery and prevent accidental stimulation.

Multi-Dog Control

If you are training two dogs, ensure each receiver is paired to a different channel on your remote transmitter. Your remote will have a selector to switch between Channel 1 and Channel 2, allowing you to control each dog independently.

Maintenance

• Cleaning: Regularly clean the receiver and contact points with a damp cloth. Ensure the device is dry before charging or use.
• Contact Points: Periodically check the contact points for wear or damage. Ensure they are securely attached and free from debris. The conductive silicone covers should also be inspected for integrity.
• Battery Care: To prolong battery life, avoid fully discharging the receiver frequently. Charge the device when the battery indicator is low. If storing for an extended period, charge the battery to about 50% and recharge every few months.
• Strap Inspection: Check the collar strap for signs of wear, fraying, or damage. Replace if necessary to ensure secure fit and function.

Troubleshooting

Specifications

• Brand: PATPET
• Model: P Collar 680 Receiver
• Item Weight: 3.84 ounces
• Item Package Dimensions: 3.46 x 3.39 x 1.73 inches
• Batteries: Lithium Ion batteries (included, required)
• Waterproof Rating: IPX7
• Material: Silicone (for conductive covers)
• Color: Grey (receiver unit)
• Target Audience: Dogs
• Age Range Description: All life stages
• Breed Recommendation: Small, Medium, Large
• Date First Available: October 12, 2022

Warranty and Support

For detailed warranty information, please refer to the documentation included with your product packaging or visit the official PATPET website. For technical support or customer service inquiries, please contact PATPET customer support through their official channels.

Important Notes

• This product is a receiver unit only and requires a compatible PATPET remote transmitter for operation.
• Always use training collars responsibly and humanely. Consult with a professional dog trainer if you are unsure about proper training techniques.
• Regularly check your dog's neck for any signs of irritation or sores from the collar.