1. Product Overview
The AQUASTRONG 1.6 HP Shallow Well Pump with Pressure Tank is designed for efficient water boosting and irrigation in home, garden, and lawn applications. This automatic water booster jet pump features a stainless steel construction and an integrated pressure tank, providing reliable water supply for various needs.
Figure 1: AQUASTRONG 1.6 HP Shallow Well Pump with Pressure Tank.
2. Safety Information
Always observe the following safety precautions to prevent injury or damage to the pump:
- Ensure the pump is properly grounded to prevent electrical shock.
- Do not operate the pump with damaged electrical cords or plugs.
- Disconnect power before performing any maintenance or service.
- Protect the pump from freezing temperatures to prevent damage.
- Ensure adequate ventilation around the pump to prevent overheating.
- The pump is designed for water temperatures between 4°C (39°F) and 40°C (104°F). Operating outside this range may cause damage.
- Install a check valve at the inlet pipe to prevent dry running and ensure proper operation.
3. Setup and Installation
The AQUASTRONG pump features an all-in-one compact design for easy installation. Follow these steps for proper setup:
- Placement: Position the pump on a stable, level surface. Ensure it is protected from direct weather exposure.
- Connections:
- Connect the 1" NPT Inlet pipe to your water source.
- Connect the 1" NPT Discharge pipe to your irrigation or water distribution system.
- Important: A check valve (not included) MUST be installed at the inlet pipe to prevent dry running and ensure less frequent priming.
- Electrical Connection: Plug the 6.5' UL Power Cord into a grounded 115V power outlet.
- Priming: Before initial operation, the pump must be properly primed. Fill the pump casing with water through the designated priming port until it overflows. Ensure all air is removed from the pump and suction line.
Figure 2: Key components including 1" NPT Inlet, 1" NPT Discharge, Stainless Steel Tank Supply Connector, Motor, Metal Bracket, 5-gallon pressure tank, Pressure Gauge, Support Feet, and 6.5' UL Power Cord.
Figure 3: The pump's compact design facilitates easy installation and simple operation.
4. Operating Instructions
Once installed and primed, the pump is ready for operation. The integrated 5-gallon pressure tank is pre-assembled and the pressure switch is set to operate between 20 PSI (cut-in) and 40 PSI (cut-out).
- Power On: Activate the power switch on the pump. The pump will begin to build pressure.
- Pressure Monitoring: The 0-86 PSI pressure gauge allows for timely observation of water pressure.
- Automatic Operation: The pump will automatically turn on when pressure drops to 20 PSI and turn off when it reaches 40 PSI, maintaining consistent water pressure.
- Thermal Overload Protection: The pump is equipped with thermal overload protection, which automatically shuts off the pump if it detects dry running or overheating. This protects the motor and extends service life.
- Ventilation: The large fan-cooled ventilation system offers strong heat dissipation, contributing to longer service life.
Figure 4: Close-up of the 5-gallon pressure tank, pressure gauge, and motor with thermal overload protection and fan-cooled ventilation.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your AQUASTRONG pump:
- Regular Inspection: Periodically check all connections for leaks and ensure the power cord is in good condition.
- Cleanliness: Keep the pump and surrounding area clean and free of debris to ensure proper ventilation.
- Winterization: If the pump will be exposed to freezing temperatures, drain all water from the pump and pipes to prevent damage from ice expansion.
- Protection: Consider covering the pump with a small structure that allows adequate airflow to protect it from rain and other environmental elements.
6. Troubleshooting
Refer to the following table for common issues and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start or hums but doesn't pump. | Lack of prime, air in system, motor issue, thermal overload. | Ensure pump is fully primed and all air is removed. Check power supply. Allow motor to cool if thermal overload tripped. If issue persists, contact customer support. |
| Pump cycles on and off frequently. | Leaking pipes/fixtures, pressure tank issue (e.g., burst bladder), pressure switch malfunction. | Inspect plumbing for leaks. Check pressure tank air charge. If the internal bladder is suspected to be burst, the tank may need replacement. Consult a qualified technician. |
| Water leaks from connections. | Loose fittings, improper thread sealant, damaged threads. | Tighten all connections. Ensure proper use of thread sealant (e.g., PTFE tape or pipe dope) on NPT threads. If threads are damaged, replacement of components may be necessary. |
| Low water pressure. | Insufficient priming, clogged inlet/outlet, worn pump components. | Re-prime the pump. Check for obstructions in the inlet and outlet pipes. If the pump is old, internal components may be worn and require professional service. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | AQUASTRONG |
| Model Number | PGA150SA |
| Horsepower | 1.6 HP |
| Maximum Flow Rate | 1320 GPH (Gallons Per Hour) |
| Voltage | 115V |
| Material | Stainless Steel (pump head) |
| Pressure Tank Capacity | 5 Gallons (pre-charged) |
| Cut-in Pressure | 20 PSI |
| Cut-out Pressure | 40 PSI |
| Maximum Lifting Height | 164 Feet |
| Product Dimensions (L x W x H) | 17.9" x 10.9" x 19.7" |
| Item Weight | 38.4 pounds |
| Operating Water Temperature | 4°C to 40°C (39°F to 104°F) |
Figure 5: Dimensional overview of the AQUASTRONG pump.
8. Warranty and Customer Support
AQUASTRONG is committed to providing quality products and customer satisfaction. While specific warranty details are not provided in this manual, customers have reported positive experiences with manufacturer support for product issues.
For any questions, technical assistance, or warranty claims, please contact AQUASTRONG customer service through their official channels. Keep your purchase receipt and product model number (PGA150SA) readily available for faster service.
You can visit the AQUASTRONG Store for more information: AQUASTRONG Store
