Introduction
The Fujifilm VG-XH Vertical Battery Grip is an essential accessory designed to enhance the functionality and ergonomics of your Fujifilm X-H2S or X-H2 camera. This grip provides extended battery life, improved handling for vertical shooting, and additional control buttons for seamless operation.
It is engineered to be weather-resistant, ensuring reliable performance in various environmental conditions. By accommodating two NP-W235 rechargeable lithium-ion batteries, it significantly extends shooting time, offering up to 1700 frames between recharges.
What's in the Box
- Vertical Battery Grip (VG-XH)
Key Features
- Weather Resistant: Designed to withstand various weather conditions, protecting your equipment.
- Extended Battery Life: Accepts two NP-W235 lithium-ion rechargeable batteries, significantly increasing shooting capacity.
- Performance Modes: Features a toggle switch for Eco, Normal, and Boost performance modes, allowing optimization for different shooting scenarios.
- Integrated Controls: Incorporates a secondary shutter release button, focus lever, Q Button, AE-L button, AF-ON button, and front and rear command dials for comfortable vertical shooting.
Setup and Installation
Figure 1: Main view of the Fujifilm VG-XH Vertical Battery Grip. This image shows the overall design and the camera attachment point.
Figure 2: Side view of the VG-XH grip, highlighting the battery compartment latch and the camera mounting screw.
1. Battery Installation
- Ensure the camera and grip are powered off.
- Locate the battery compartment on the grip (refer to Figure 2).
- Open the battery compartment latch.
- Insert two fully charged NP-W235 batteries into the grip, ensuring correct orientation according to the polarity indicators.
- Close the battery compartment latch securely until it clicks into place.
2. Attaching the Grip to the Camera
- Remove the battery from your Fujifilm X-H2S/X-H2 camera body.
- Remove the camera's battery compartment cover. This cover can typically be stored in a designated slot on the grip (if available, otherwise keep it safe).
- Align the mounting screw of the VG-XH grip with the tripod socket on the bottom of your camera.
- Gently slide the grip onto the camera, ensuring the electrical contacts on both the camera and the grip align properly.
- Tighten the mounting screw securely by rotating the thumbwheel on the grip until the grip is firmly attached to the camera body. Do not overtighten.
Operating the Grip
Figure 3: Top view of the VG-XH grip, showing the integrated controls for vertical shooting.
1. Secondary Controls
The VG-XH grip provides a full set of controls mirrored from the camera body, optimized for comfortable vertical shooting. These include:
- Shutter Release Button: For capturing photos.
- Focus Lever: To quickly adjust focus points.
- AE-L Button: For Auto Exposure Lock.
- AF-ON Button: For Auto Focus On.
- Q Button: Accesses the Quick Menu.
- Fn Button: A customizable function button.
- Front and Rear Command Dials: For adjusting settings like aperture, shutter speed, and exposure compensation.
Ensure the grip's lock switch (if present, typically near the shutter button) is in the "unlocked" position to enable these controls.
2. Performance Modes
A toggle switch on the grip allows you to select between different performance modes, affecting battery consumption and camera responsiveness:
- ECO Mode: Prioritizes battery conservation, ideal for extended shooting sessions where maximum performance is not critical.
- NORMAL Mode: Standard performance mode, offering a balance between battery life and responsiveness.
- BOOST Mode: Maximizes camera performance and responsiveness, suitable for demanding shooting situations like high-speed continuous shooting or video recording. Note that this mode will consume battery power more rapidly.
Maintenance and Care
- Cleaning: Use a soft, dry cloth to clean the exterior of the grip. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid using strong solvents or abrasive cleaners.
- Contacts: Periodically inspect the electrical contacts on both the grip and your camera for dust or debris. Clean them gently with a dry, lint-free cloth if necessary.
- Storage: When not in use for extended periods, remove batteries from the grip. Store the grip in a cool, dry place, away from direct sunlight and extreme temperatures.
- Weather Resistance: While weather-resistant, avoid intentionally exposing the grip to heavy rain, snow, or dust. Always ensure the battery compartment is securely closed when in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Grip controls not responding. | Grip lock switch is engaged. | Ensure the lock switch on the grip is in the "unlocked" position. |
| Camera not recognizing batteries in the grip. | Batteries incorrectly inserted or not charged; poor contact with camera. |
|
| Grip feels loose on camera. | Mounting screw not tightened sufficiently. | Tighten the mounting screw on the grip until it is secure. Do not overtighten. |
Specifications
| Model Number | VG-XH (Item model number: 16757320) |
| Compatible Cameras | Fujifilm X-H2S, Fujifilm X-H2 |
| Battery Type | NP-W235 (x2) |
| Dimensions (L x W x H) | 6.3 x 3.9 x 3.1 inches (approx.) |
| Weight | 15.4 ounces (approx.) |
| Color | Black |
| UPC | 074101205855 |
Warranty Information
This Fujifilm product is covered by a limited manufacturer's warranty. Please refer to the warranty card included with your purchase or visit the official Fujifilm website for detailed terms and conditions, including warranty period and coverage specifics. Keep your proof of purchase for warranty claims.
Customer Support
For technical assistance, service, or further inquiries regarding your Fujifilm VG-XH Vertical Battery Grip, please contact Fujifilm customer support or visit their official website. You can find contact information and support resources at the Fujifilm Store on Amazon or the main Fujifilm support portal.