1. Introduction
This manual provides essential instructions for the safe and effective use, charging, maintenance, and storage of your TATTU Plus 22000mAh 22.2V 25C 6S Lipo Smart Battery Pack. Please read this manual thoroughly before using the battery to ensure proper operation and to prevent damage or injury. Retain this manual for future reference.
2. Safety Guidelines
Lithium Polymer (LiPo) batteries are powerful and can be dangerous if not handled correctly. Failure to follow these safety instructions can result in fire, personal injury, and property damage.
- Charging: Always use a LiPo-compatible charger with a balance function. Never charge unattended. Charge in a fire-safe area, away from flammable materials. Do not charge damaged or swollen batteries.
- Discharging: Do not over-discharge the battery. Stop use immediately if the battery voltage drops below 3.0V per cell (18.0V for a 6S pack). Over-discharging can cause permanent damage and fire risk.
- Storage: Store batteries at room temperature (15-25°C or 59-77°F) and at a storage voltage of approximately 3.8V per cell (22.8V for a 6S pack). Keep away from direct sunlight, heat sources, and moisture.
- Handling: Do not puncture, crush, short-circuit, or disassemble the battery. Avoid dropping the battery. If the battery is damaged, discontinue use immediately and dispose of it properly.
- Temperature: Do not expose the battery to extreme temperatures. Operating temperature range is typically 0-50°C (32-122°F).
- Disposal: Dispose of LiPo batteries according to local regulations. Never dispose of them in household waste. Fully discharge the battery before disposal.
3. Product Overview
The TATTU Plus 22000mAh 22.2V 25C 6S Lipo Smart Battery Pack is designed for high-performance applications, offering reliable power and a long cycle life. It features robust construction and specific connectors for optimal compatibility.
Figure 3.1: Connectors and High Capacity. This image provides a detailed view of the battery's connectors: the JST-XHR-7P for balancing and the XT150+AS150 for power discharge. It also emphasizes the battery's high capacity.
Key Features:
- High Capacity: 22000mAh for extended run times.
- High Discharge Rate: 25C continuous discharge for demanding applications.
- Advanced Cell Technology: Stable automatic stacking technology for consistent performance.
- Quality Materials: Superior Japan and Korea Lithium Polymer raw materials.
- Connectors: Equipped with XT150+AS150 discharge plug and JST-XHR-7P balancer connector.
4. Technical Specifications
Refer to the table below for detailed technical specifications of your TATTU Plus battery pack.
Figure 4.1: Basic Parameters. This image displays the key technical specifications of the battery, such as its 22000mAh capacity, 22.2V voltage, 25C discharge rate, 6S1P cell configuration, and XT150+AS150 discharge plug.
| Parameter | Value |
|---|---|
| Minimum Capacity | 22000mAh |
| Configuration | 6S1P / 22.2V / 6 cells |
| Discharge Rate | 25C |
| Max Burst Discharge Rate | 50C |
| Net Weight (±20g) | 2559g (5.64 pounds) |
| Dimensions | 213 x 95 x 68mm (8.39 x 3.74 x 2.68 inches) |
| Discharge Plug | XT150+AS150 |
| Balancer Connector Type | JST-XHR-7P |
| Battery Cell Composition | Lithium Polymer |
5. Setup & First Use
5.1 Package Contents
Figure 5.1: Package Included. This image displays the items included in the product package: one TATTU Plus 6S 25C 22000mAh Lipo Battery, a user manual, and the product's retail packaging box.
Upon opening the package, verify that all items are present and undamaged:
- 1x TATTU Plus 6S 25C 22000mAh Lipo Battery
- 1x User Manual
- 1x Wrapped Box
5.2 Initial Charging
Before first use, it is recommended to fully charge the battery. Follow these steps:
- Connect the XT150+AS150 discharge plug to your LiPo-compatible charger's main output.
- Connect the JST-XHR-7P balancer connector to the charger's balance port.
- Set your charger to the correct LiPo charging mode (e.g., 'LiPo Balance Charge').
- Set the charging voltage to 22.2V (6S) and the charging current to 1C (22A for a 22000mAh battery). Refer to your charger's manual for specific settings.
- Begin charging and monitor the process closely. Never leave charging batteries unattended.
6. Operating Instructions
6.1 Connecting the Battery
Ensure your device (e.g., drone, RC vehicle) is powered off before connecting the battery.
- Carefully align the XT150+AS150 discharge plug with the corresponding connector on your device.
- Push the connectors firmly together until they are fully seated.
- Ensure the battery is securely mounted in your device to prevent movement during operation.
6.2 During Use
- Monitor battery voltage during operation. Do not allow the voltage to drop below 3.0V per cell (18.0V for a 6S pack) to prevent irreversible damage.
- Avoid excessive current draw that exceeds the battery's continuous discharge rating (25C).
- If the battery becomes excessively hot during use, discontinue operation immediately and allow it to cool down before further handling.
Figure 6.1: Strong Endurance. This image illustrates the battery's application in various drone setups, emphasizing its strong endurance and suitability for demanding aerial tasks. It shows the battery alongside different types of multi-rotor aircraft.
7. Maintenance & Storage
7.1 General Maintenance
- Regularly inspect the battery for any signs of damage, swelling, or loose connections.
- Keep connectors clean and free from dirt or corrosion.
- Avoid physical impact or dropping the battery.
7.2 Long-Term Storage
For optimal battery life and safety during long-term storage (more than 7 days):
- Discharge or charge the battery to a storage voltage of 3.8V per cell (22.8V for a 6S pack). Most LiPo chargers have a 'Storage' mode.
- Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures (ideal: 15-25°C or 59-77°F).
- Store in a fire-resistant container or LiPo-safe bag.
7.3 Cycle Life
Figure 7.1: Advantage/Discharge Rate Curve. This image highlights the performance advantages of the TATTU battery, featuring a discharge rate curve that demonstrates its superior performance compared to other brands. Key benefits include a long cycle life, excellent overall performance, low internal resistance, and high current delivery capabilities.
The TATTU Plus battery is designed for a long cycle life, with at least 150 cycles under proper care. Following the charging, discharging, and storage guidelines will help maximize the battery's lifespan.
8. Troubleshooting
If you encounter issues with your TATTU Plus battery, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Incorrect charger settings, faulty connections, damaged battery. | Verify charger settings (LiPo mode, voltage, current). Check all connections. If battery is swollen or damaged, discontinue use and dispose of safely. |
| Battery swells during charging/use | Overcharging, over-discharging, internal damage, excessive heat. | Immediately disconnect and place in a fire-safe area. Do NOT use. Dispose of safely. This indicates a serious safety risk. |
| Reduced run time | Aging battery, improper charging/storage, over-discharging. | Ensure proper charging and storage. Avoid over-discharging. Battery capacity naturally degrades over time. |
| Battery gets hot during use | Excessive current draw, short circuit, internal resistance. | Reduce load on the battery. Check for short circuits in your device. If heat is extreme, discontinue use. |
9. Warranty & Support
TATTU provides local after-sales service for its products. For any warranty claims, technical support, or inquiries regarding your TATTU Plus 22000mAh 22.2V 25C 6S Lipo Smart Battery Pack, please contact our customer service team. Our local after-sales service is located in Dublin, CA.
Please have your purchase information and battery details ready when contacting support to facilitate a quicker resolution.
