1. Introduction
This manual provides comprehensive instructions for the PERFASCIN RUE-4202, RUE-4203, and RUE-4350 replacement remote controls. These remotes are designed to function with a wide range of Alpine MP3 WMA CD Receivers, offering convenient control over your audio system.
Compatible Models (Partial List):
- For RUE-4202: 97-02291Z01, CDA-117, CDA-123, CDA-9853, CDA-9853R, CDA-9883, CDA-9883R, CDA-9885, CDA-9886M, CDE-122, CDE-124SXM, CDE-133BT, CDE-135BT, CDE-136BT, CDE-141, CDE-HD137BT, CDE-HD138BT, CDE-W235BT, INE-S920HD, INE-Z928HD, IVE-W535, IVE-W930, SXV-100A.
- For RUE-4203: 97-02173Z01, IVAD100, IVAW505, IVAD310, DVA9816, IVAW203, IVAD106, DVA9965, IVAW200, INAW900BT, IVAD105, DVA9860, IVAW205, INAW910, RUE-4190, DVA9861.
- For RUE-4350: Compatible with various Alpine units.
Image 1.1: Front view of the PERFASCIN replacement remote control.
2. Setup
2.1 Battery Installation
The remote control requires two (2) 1.5V AAA alkaline batteries (not included). Follow these steps to install the batteries:
- Locate the battery compartment on the back of the remote control.
- Press down on the tab and slide the battery cover off.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery cover back into place until it clicks securely.
Image 2.1: Battery compartment with cover removed.
2.2 Initial Use
This is an infrared (IR) replacement remote control. No programming or pairing is required. Once the batteries are correctly installed, the remote is ready for use with your compatible Alpine MP3 WMA CD Receiver.
3. Operating Instructions
To operate your Alpine unit, point the remote control directly at the infrared sensor on your receiver and press the desired button. Ensure there are no obstructions between the remote and the receiver.
3.1 Key Functions Overview
The remote control features various buttons for common functions:
- PWR (Power): Turns the receiver on or off.
- SRC (Source): Cycles through available audio sources (e.g., CD, Radio, USB, AUX).
- BAND: Selects radio bands (e.g., FM1, FM2, AM).
- SETUP: Accesses the system setup menu.
- AUDIO: Adjusts audio settings (e.g., bass, treble, balance).
- MUTE: Mutes or unmutes the audio output.
- VOLUME (+/-): Increases or decreases the audio volume.
- MENU: Navigates through menus.
- Navigation Buttons (Up, Down, Left, Right, ENT): Used for menu navigation and selection.
- Playback Controls (Play/Pause, Skip Forward/Backward): Controls media playback.
- Number Buttons (0-9): For direct track selection, radio station presets, or numerical input.
- CLR (Clear): Clears input or selection.
- MONITOR: Controls display or monitor functions (if applicable to your receiver).
Note: Specific button functions may vary slightly depending on your Alpine receiver model. Refer to your Alpine receiver's original user manual for detailed function descriptions.
Image 3.1: Detailed view of remote control buttons.
4. Maintenance
4.1 Battery Replacement
Replace batteries when the remote control's response becomes sluggish or stops working. Always replace both batteries at the same time with new 1.5V AAA alkaline batteries. Do not mix old and new batteries, or different types of batteries.
4.2 Cleaning
To clean the remote control, wipe it with a soft, dry cloth. Do not use liquid cleaners, sprays, or abrasive materials, as these can damage the remote's surface or internal components.
4.3 Storage
Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. If the remote will not be used for an extended period, it is recommended to remove the batteries to prevent leakage.
5. Troubleshooting
If you experience issues with your remote control, please refer to the following common troubleshooting steps:
- Remote not responding:
- Check if the batteries are installed correctly with the correct polarity.
- Replace the batteries with fresh 1.5V AAA alkaline batteries.
- Ensure there is a clear line of sight between the remote control and the Alpine receiver's IR sensor. Remove any obstructions.
- Confirm that the remote is pointed directly at the receiver.
- Remote functions are incorrect or limited:
- Verify that your Alpine receiver model is listed as compatible with this remote.
- Some advanced functions may require specific settings on your Alpine receiver. Consult your Alpine receiver's original user manual for details.
If the problem persists after trying these steps, please contact customer support for further assistance.
6. Specifications
| Feature | Specification |
|---|---|
| Product Dimensions | 7 x 2 x 0.65 inches |
| Item Weight | 2.3 ounces |
| Batteries Required | 2 AAA batteries (not included) |
| Compatible Devices | Alpine MP3 WMA CD Receivers (various models, see Section 1) |
| Model Number | ANG-RUE-4202-4203-4350-US |
| Max Number of Supported Devices | 1 |
7. Warranty and Support
7.1 Product Support
For any questions regarding the compatibility or operation of your PERFASCIN replacement remote control, please contact our customer service team. We are available to provide professional assistance and guidance.
7.2 Contact Information
Please refer to the retailer's website or your purchase documentation for specific customer service contact details for PERFASCIN products.