Hormann LineaMatic P2 Gate Actuator Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Hormann LineaMatic P2 sliding gate actuator. Please read these instructions carefully before beginning any work on the gate system. The LineaMatic P2 is designed for automating sliding gates, offering reliable performance with adjustable speed and robust construction.

2. Safety Instructions

Important Safety Information: Failure to follow these instructions may result in serious injury or property damage.

• Installation and maintenance must be performed by qualified personnel only.
• Ensure the main power supply is disconnected before any installation, maintenance, or repair work.
• Keep hands, feet, and clothing clear of the gate and actuator during operation.
• Do not allow children to play with or near the gate or its controls.
• Regularly check all safety devices (e.g., photocells, safety edges) for proper function.
• The gate must be in good mechanical condition and balanced before installing the actuator.
• Ensure all local safety regulations and standards are met during installation.

3. Package Contents

Verify that all components are present in the package:

• 1x Hormann LineaMatic P2 Gate Motor
• 1x Hand Transmitter (remote control)
• 1x 868 MHz Receiver
• Mounting Material (screws, anchors, etc.)
• 1x Drive Pinion Module 4 (straight teeth)
• 1x Mounting Aid for Rack Alignment
• Corrosion-resistant and height-adjustable housing (pre-assembled with motor)

4. Setup and Installation

The installation process involves mounting the actuator, installing the gate rack, and connecting the electrical components. Refer to the detailed diagrams in the manufacturer's full installation guide for precise measurements and steps.

4.1 Mounting the Actuator

Position the actuator on a stable, level surface next to the gate opening. The compact, height-adjustable housing allows for flexible placement. Secure the actuator firmly using the provided mounting material.

4.2 Installing the Gate Rack

Attach the drive pinion module 4 to the actuator. Use the included mounting aid to ensure correct alignment of the rack along the bottom edge of the sliding gate. The rack must be securely fastened to the gate, allowing for smooth engagement with the actuator's pinion.

Image: Hormann LineaMatic P2 gate actuator installed next to a white sliding gate, showing the compact housing and the rack system. This image illustrates the typical setup of the actuator with a sliding gate.

4.3 Electrical Connection

Connect the actuator to a 230-240 V AC mains supply. Ensure all electrical connections are made according to local electrical codes and the wiring diagram provided in the complete manual. The integrated electronic control unit is located within the actuator housing.

4.4 Initial Setup and Limit Switches

After power-up, configure the gate's opening and closing limits. The LineaMatic P2 uses magnetic limit switches for precise positioning. Follow the programming steps in the full manual to teach the actuator the gate's travel path. The speed of the gate can be individually adjusted during this process to ensure uniform operation.

5. Operating Instructions

The LineaMatic P2 gate actuator is operated via the supplied hand transmitter or optional wired controls.

5.1 Using the Hand Transmitter

Press the designated button on the hand transmitter to open or close the gate. A single press typically initiates movement, another press stops it, and a third press reverses the direction.

5.2 Individual Passage Programming

The system allows for programming an 'individual passage' function, which opens the gate only partially for pedestrian access. Refer to the full manual for steps on how to set up and activate this feature.

5.3 Automatic Closing Function

The integrated automatic closing function can be enabled, causing the gate to close automatically after a set delay once it has fully opened. Ensure all safety devices are correctly installed and functioning before activating this feature.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your LineaMatic P2 gate actuator.

• Monthly: Check the gate's mechanical condition. Ensure it moves freely and smoothly by hand (with the actuator disengaged).
• Quarterly: Inspect the rack for wear or damage. Clean any debris from the rack and pinion.
• Annually: Have a qualified technician inspect the entire system, including electrical connections, safety devices, and actuator components.
• Keep the actuator housing clean and free from dirt, dust, and moisture.
• Do not use harsh chemicals for cleaning.

7. Troubleshooting

If you encounter issues with your LineaMatic P2, consult the following basic troubleshooting guide. For complex problems, contact a qualified technician.

• Gate does not move: Check power supply, ensure the actuator is plugged in, and verify that safety devices (e.g., photocells) are not obstructed or faulty.
• Remote control not working: Replace the battery in the hand transmitter. Re-pair the remote if necessary (refer to the full manual).
• Gate stops unexpectedly: This could indicate an obstruction or a fault in a safety device. Clear any obstructions and check safety sensors. The adjustable force limitation feature will stop the gate if it encounters resistance.
• Gate opens/closes partially: Re-calibrate the limit switches.

8. Technical Specifications

9. Warranty Information

Hormann products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Hormann website. Keep your proof of purchase for warranty claims.

10. Support

For further assistance, technical support, or spare parts, please contact your authorized Hormann dealer or visit the official Hormann website. You can find contact information and additional resources there.

Hormann Official Website: www.hormann.com