1. Product Overview
The FUN PAC Camping Sleeping Pad (Model CQD-VC-US-G) is an ultralight, inflatable sleeping mat designed for outdoor activities such as camping, backpacking, hiking, and traveling. It features a built-in foot pump for quick inflation and an integrated pillow for enhanced comfort. The pad is constructed from durable 40D nylon with a TPU coating, offering resistance to wear, water, and tears.
Key features include:
- Extra Wide & 3" Thick Sleep Support: Provides insulation from uneven ground and hard rocks.
- Integrated Pillow: Designed to relieve neck pressure.
- Built-in Foot Pump: Allows for rapid inflation (30-60 seconds) without external pumps or mouth inflation.
- Ultralight & Compact: Weighs approximately 1.5 pounds and packs down to the size of a water bottle for easy portability.
- Durable Construction: Made from 40D nylon and TPU coating for resistance to wear, water, and tears.
- Connectable Design: Equipped with side buttons to easily connect multiple pads for a wider sleeping area.
2. Package Contents
Your FUN PAC Camping Sleeping Pad package should contain the following items:
- 1 x FUN PAC Camping Sleeping Pad (Model CQD-VC-US-G)
- 1 x Carry Bag
- 1 x Instruction Manual (this document)
3. Setup Instructions
3.1 Unpacking and Unfolding
- Remove the sleeping pad from its carry bag.
- Unroll the pad completely and lay it flat on a clean, smooth surface. Ensure the built-in pillow is at the desired head end.
3.2 Inflation using Built-in Foot Pump
The FUN PAC Sleeping Pad features a built-in foot pump for convenient and rapid inflation.
- Locate the inflation valve on the foot pump section of the pad (typically near the foot end).
- Open the valve cap. Ensure the inner flap is closed to prevent air from escaping.
- Place your foot or hand over the pump area and press down firmly. Lift your foot/hand to allow air to enter the pump chamber. Repeat this action.
- Continue pumping until the pad reaches your desired firmness. This typically takes 30-60 seconds.
- Once inflated, securely close the valve cap to prevent air leakage.
3.3 Connecting Multiple Pads (Optional)
For a larger sleeping area, two or more FUN PAC Sleeping Pads can be connected using the side buttons.
- Lay two pads side-by-side.
- Align the snap buttons located along the edges of both pads.
- Press the buttons firmly to secure the pads together. It is recommended to connect the pads before full inflation for easier alignment.
4. Operation
Once inflated, the FUN PAC Sleeping Pad is ready for use. The ergonomic design with egg-shaped air cells and integrated pillow provides comfortable support for various sleeping positions.
5. Deflation and Storage
5.1 Deflation
- Locate the deflation valve (usually a larger valve, distinct from the inflation valve).
- Open the deflation valve completely. Air will rapidly escape from the pad.
- To expedite deflation, gently roll or press the pad from the end opposite the valve towards the valve, pushing out any remaining air.
5.2 Folding and Packing
- Once deflated, fold the pad lengthwise into thirds or halves, depending on its width.
- Starting from the end opposite the valve, tightly roll the pad towards the valve. This helps to expel any residual air and achieve a compact size.
- Secure the rolled pad with any integrated straps or bands, then place it back into the provided carry bag.
6. Maintenance
- Cleaning: Wipe the surface of the pad with a damp cloth and mild soap. Rinse thoroughly and allow to air dry completely before storing. Do not machine wash or tumble dry.
- Storage: Store the deflated and rolled pad in its carry bag in a cool, dry place away from direct sunlight and sharp objects.
- Puncture Repair: In case of a small puncture, use a standard inflatable repair kit (not included) to patch the affected area.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pad does not inflate or inflates slowly. | Inflation valve not properly sealed; inner flap open; insufficient pumping. | Ensure the inner flap of the inflation valve is closed. Press down firmly and lift completely during pumping. Check for any obstructions in the valve. |
| Pad loses air quickly. | Valve caps not securely closed; small puncture or leak. | Verify both inflation and deflation valve caps are tightly closed. Inspect the pad for punctures. Use a repair kit for small holes. |
| Difficulty deflating. | Deflation valve not fully open; air trapped. | Ensure the deflation valve is fully open. Roll the pad tightly from the opposite end to force air out. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | CQD-VC-US-G (ZW-DRCQD-XJ) |
| Brand | FUN PAC |
| Size | Single |
| Color | Single-green |
| Product Dimensions (Inflated) | 75"L x 25"W x 6.7"Th (approx. 190.5 cm L x 63.5 cm W x 17 cm Th) |
| Item Thickness | 3 Inches (approx. 7.6 cm) |
| Item Weight | 1.5 pounds (approx. 0.68 kg) |
| Material | 40D Nylon with TPU Coating |
| Special Feature | Compact, Built-in Foot Pump, Integrated Pillow, Connectable |
| Capacity | 400 Pounds (approx. 181 kg) |
| Target Audience | Adult |
| UPC | 704444255797 |
9. Safety Information
- Do not over-inflate the sleeping pad.
- Keep away from open flames, extreme heat, and sharp objects.
- Not intended for use as a flotation device.
- Ensure the pad is placed on a relatively flat surface free of debris to prevent damage.
10. Warranty and Support
FUN PAC offers a 1-year warranty for this product. In case of defective products, a full refund or free replacement is available without the need for return. For any questions, concerns, or support needs, please contact FUN PAC customer service.
Contact information can typically be found on the product packaging or the official FUN PAC website.