Welcome
Thank you for choosing the KOMIGAN Motion-Activated Cascading Effect LED Stair Lighting Kit. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new lighting system. Please read it thoroughly before beginning installation.
Safety Information
- Ensure power is disconnected before installation or maintenance.
- This product is designed for indoor use only.
- Consult a qualified electrician if you are unsure about any wiring procedures.
- Keep all components away from water and moisture.
What's in the Box
Your KOMIGAN KMG-3233 kit includes the following components:
- LED Light Bars (Quantity: 16 for this model)
- Motion Sensors (2 units)
- Daylight Sensor
- Controller (KMG-3233)
- Power Supply
- Power Cord
- LED Light Extension Cords
- Sensor Extension Cords
- Mounting Hardware (metal clips, double-sided adhesive)
Image: All components included in the KOMIGAN KMG-3233 LED Stair Lighting Kit.
Installation Guide
Planning Your Installation
Before installation, determine the optimal placement for your LED light bars and motion sensors. Ensure stair treads are 25 inches or wider for proper fit of the 23.6-inch aluminum light bars. Plan cable routing to ensure a clean and secure setup.
Mounting the LED Light Bars
The LED light bars can be installed using either the provided double-sided adhesive or sturdy metal clips. For a secure and long-lasting installation, metal clips are recommended. Ensure the surface is clean and dry before applying adhesive.
Image: Light bar mounting options: metal clip fixing and double-sided adhesive fixing.
Installing Motion Sensors
The motion sensors can be installed via surface mounting or flush mounting. For flush mounting, drill a 20mm hole at the desired location. Position sensors at the top and bottom of the staircase to detect movement from both directions.
Image: Motion sensor installation methods: surface mounting and flush mounting.
Wiring Diagram
Connect the power supply to a 110V AC outlet. Connect the power supply output to the controller. Then, connect each LED light bar to its corresponding port on the controller (1-16). Finally, connect the upstairs, downstairs, and daylight sensors to their designated ports on the controller. Ensure all connections are secure.
Image: Comprehensive wiring diagram for the stair lighting system.
Installation Video
Video: An official KOMIGAN video demonstrating the installation process of the Motion Sensor LED Stair Lighting Kit KMG-3233.
Operating Instructions
Motion-Activated Cascading Effect
When a motion sensor detects movement, the LED lights will illuminate sequentially, creating a smooth cascading effect up or down the staircase. After a set delay, the lights will turn off in the same cascading manner.
Image: Demonstration of the motion-activated cascading light effect on a staircase.
Customizing Settings
The KMG-3233 controller allows for customization of various settings:
- Speed: Adjust the speed of the cascading light effect.
- Brightness: Control the overall brightness of the LED lights.
- Mode: Select from different lighting modes, including Motion Trigger, Stay On, Cascade, and Sync Mode.
- Delay Time: Set the duration the lights remain on after motion detection.
Refer to the controller's diagram for specific button functions and adjustments.
Operation Video
Video: An official KOMIGAN video showcasing the intelligent motion sensor LED stair lighting kit in operation, demonstrating the cascading light effect.
Care and Maintenance
To ensure the longevity and optimal performance of your KOMIGAN LED Stair Lighting Kit, follow these simple maintenance guidelines:
- Cleaning: Gently wipe the LED light bars and sensors with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the surfaces.
- Inspection: Periodically check all wiring connections to ensure they are secure. Ensure light bars and sensors remain firmly attached.
- Environment: This system is designed for indoor use. Avoid exposure to extreme temperatures, direct sunlight, or high humidity, which can affect performance and lifespan.
Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn on. | No power, loose connection, or faulty sensor. | Check power supply connection. Verify all wiring is secure. Ensure sensors are not obstructed. |
| Lights turn on/off unexpectedly. | Sensor sensitivity too high, or interference. | Adjust sensor sensitivity on the controller. Check for objects near sensors causing false triggers. |
| Cascading effect is not smooth or incorrect. | Incorrect speed setting or wiring order. | Adjust the speed setting on the controller. Double-check the wiring of light bars to ensure they are connected in sequential order. |
| Lights remain on constantly. | "Stay On" mode activated or sensor malfunction. | Check the controller mode setting. If in motion-activated mode, ensure sensors are clear and functioning correctly. |
Product Specifications
| Feature | Detail |
|---|---|
| Brand | KOMIGAN |
| Model Number | KMG-3233 |
| Color Temperature | Cool White 6000K |
| Material | Aluminum (Light Bar), Plastic (Controller/Sensors) |
| Light Fixture Form | Step Light |
| Room Type | Staircase |
| Product Dimensions (Controller) | 3.94"L x 1.97"W x 0.98"H |
| Specific Uses | Indoor use only |
| Power Source | AC (110 Volts) |
| Installation Type | Surface Mount |
| Special Feature | Corded, Motion Sensor |
| Light Source Type | LED |
| Number of Light Sources | 16 (for 16 Stairs kit) |
| Brightness | 6720 Lumens |
| Maximum Compatible Wattage | 160 Watts |
| Water Resistance Level | Not Water Resistant |
| Assembly Required | Yes |
Warranty Information
The KOMIGAN KMG-3233 LED Stair Lighting Kit comes with a limited warranty. Please retain your proof of purchase for any warranty claims. For specific terms and conditions, refer to the warranty card included in your package or contact customer support.
Customer Support
For technical assistance, troubleshooting, or product inquiries, please contact KOMIGAN customer support. Visit our official website or refer to the contact information provided in your product packaging.