Puig Anarchy Semifaring Installation and User Manual

1. Introduction

This manual provides detailed instructions for the proper installation, operation, and maintenance of your Puig Anarchy Semifaring. Please read this manual thoroughly before beginning installation to ensure correct assembly and safe use. Retain this manual for future reference.

2. Product Overview

The Puig Anarchy Semifaring is designed to offer a combination of sportiness and protection for your motorcycle, enhancing both aesthetics and aerodynamic performance.

2.1. Key Features

• Made of highly impact-resistant materials.
• Designed for great aerodynamic capacity.
• Dimensions: Approximately 18.5 inches (47 cm) high and 10.63 inches (27 cm) wide.
• Easy installation process.

2.2. Package Contents

• All necessary components for installation are included.

Figure 1: Puig Anarchy Semifaring installed on an Indian Scout motorcycle.

3. Important Safety Information

Always prioritize safety during installation and operation. Failure to follow these instructions may result in injury or damage to the product or motorcycle.

• Ensure the motorcycle is stable and turned off before beginning any work.
• Wear appropriate personal protective equipment, such as gloves and eye protection.
• If you are unsure about any step, consult a qualified motorcycle mechanic.
• Do not modify the semifaring or its mounting hardware.
• Regularly check all fasteners for tightness after installation and during routine maintenance.

4. Installation Guide

4.1. Tools Required (Typical)

• Hex key set
• Socket wrench set
• Torque wrench
• Measuring tape
• Soft cloth

4.2. Step-by-Step Installation

1. Preparation: Park the motorcycle on a level surface using a stand to ensure stability. Turn off the engine and remove the ignition key.
2. Unpack Components: Carefully unbox all semifaring components and verify that all parts listed in the package contents are present and undamaged.
3. Headlight Removal (if necessary): Depending on your specific Indian Scout model, it may be necessary to temporarily remove or adjust the headlight assembly to access mounting points. Refer to your motorcycle's service manual for specific instructions.
4. Attach Mounting Brackets: Secure the provided mounting brackets to the motorcycle's fork tubes or designated attachment points. Ensure they are aligned correctly and tightened to the manufacturer's recommended torque specifications. Do not overtighten.
5. Position Semifaring: Carefully position the semifaring onto the attached mounting brackets. Align the pre-drilled holes in the semifaring with the holes in the brackets.
6. Secure Semifaring: Use the supplied fasteners (bolts, washers, nuts) to secure the semifaring to the mounting brackets. Hand-tighten all fasteners initially.
7. Adjust Alignment: Once all fasteners are in place, adjust the semifaring for optimal alignment and desired angle. Ensure it does not interfere with steering or other controls.
8. Final Tightening: Once satisfied with the alignment, progressively tighten all fasteners to the manufacturer's recommended torque specifications. Double-check all connections for security.
9. Reinstall Headlight (if necessary): If the headlight was removed, reinstall it according to your motorcycle's service manual.
10. Final Inspection: Before riding, perform a thorough inspection to ensure all components are securely fastened and there is no interference with any motorcycle parts or controls.

Figure 2: Front view of the installed semifaring.

5. Operation

The Puig Anarchy Semifaring is a passive component designed to deflect wind and enhance the motorcycle's appearance. No specific operational steps are required beyond proper installation.

• Riding: Be aware of potential changes in wind deflection and aerodynamics, especially at higher speeds.
• Visibility: Ensure the semifaring does not obstruct your view of the road or dashboard instruments.

6. Maintenance

6.1. Cleaning

• Clean the semifaring regularly with mild soap and water.
• Use a soft cloth to avoid scratching the surface.
• Avoid abrasive cleaners or solvents, as these can damage the material.

6.2. Inspection

• Periodically inspect the semifaring and its mounting hardware for any signs of damage, cracks, or loose fasteners.
• Tighten any loose bolts or screws immediately.
• Replace any damaged components to maintain safety and performance.

7. Troubleshooting

• Vibration: If the semifaring vibrates excessively, check all mounting bolts for tightness. Ensure the brackets are securely attached to the motorcycle.
• Poor Fit: If the semifaring does not fit correctly, re-check the installation steps, ensuring all components are oriented correctly and not forced into place. Verify compatibility with your specific motorcycle model and year.
• Wind Noise: Minor changes in wind noise are normal. If noise is excessive, ensure the semifaring is securely mounted and not loose.

8. Technical Specifications

Figure 3: Semifaring dimensions diagram.

9. Warranty and Support

9.1. Warranty Information

This product is covered by the manufacturer's standard warranty against defects in materials and workmanship. Please refer to the official Puig website or your purchase documentation for specific warranty terms and conditions.

9.2. Customer Support

For technical assistance, missing parts, or warranty claims, please contact Puig customer support through their official website or the retailer from whom you purchased the product. Have your model number (21092N) and proof of purchase ready.