Introduction
This manual provides essential instructions for the safe and effective use of your BORNMIO 1200mAh Ni-MH replacement battery. This battery is designed for compatibility with various Aiwa portable audio devices, including models such as AM-ST40, HS-PX787, AM-HX150, AM-NX1, AM-HX400, RP-BP61, HHF-AZ01T, AM-HX30, AM-HX70, AM-CL33, AM-HX200, HS-PX587, AM-HX50, AM-HX100, MHB 901, AM-HX300, AM-HX55, and AM-F90. Please read this manual thoroughly before installation and use.
Safety Information
Observe the following safety precautions to prevent damage to the battery or your device, and to avoid personal injury:
- Do not disassemble, crush, puncture, or short-circuit the battery.
- Do not expose the battery to high temperatures (above 60°C / 140°F) or direct sunlight.
- Do not dispose of the battery in fire or water.
- Keep the battery away from children.
- Use only compatible chargers designed for Ni-MH batteries.
- If the battery shows signs of swelling, leakage, or damage, discontinue use immediately.
- Recycle used batteries responsibly according to local regulations.
Setup and Installation
Follow these steps to install your new BORNMIO replacement battery:
- Unpack the Battery: Carefully remove the battery from its packaging. Inspect it for any visible damage.
- Prepare Your Device: Ensure your Aiwa portable audio device is powered off and disconnected from any power source.
- Remove Old Battery: Open the battery compartment of your device. Carefully remove the old battery, noting its orientation.
- Insert New Battery: Insert the BORNMIO replacement battery into the compartment, ensuring the polarity (+ and - terminals) matches the markings inside the device. Do not force the battery into place.
- Secure Compartment: Close the battery compartment securely.
Image: Top view of the BORNMIO Ni-MH 1200mAh replacement battery, showing its green casing and printed specifications.
Operating Instructions
Initial Charging
For optimal performance, it is recommended to fully charge the battery before its first use. Connect your Aiwa device with the newly installed BORNMIO battery to its original or a compatible charger. The charging indicator on your device will typically show when charging is in progress and when it is complete.
Regular Use and Charging
Charge the battery whenever your device indicates a low power level. Ni-MH batteries do not suffer from a significant "memory effect" like older battery types, but occasional full discharge and recharge cycles can help maintain capacity over time. Avoid completely draining the battery repeatedly, as this can shorten its lifespan.
Maintenance and Care
- Storage: If storing the battery for an extended period, charge it to approximately 50% capacity and store it in a cool, dry place away from direct sunlight. Recharge it every 3-6 months to prevent deep discharge.
- Cleaning: Keep the battery terminals clean and dry. Use a soft, dry cloth to wipe away any dust or debris.
- Temperature: Avoid exposing the battery to extreme temperatures, both hot and cold, as this can degrade performance and lifespan.
- Disposal: Do not dispose of the battery with household waste. Consult your local waste management facility for proper recycling or disposal options for Ni-MH batteries.
Image: Angled view of the BORNMIO Ni-MH 1200mAh replacement battery, highlighting its terminals.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Charger not connected properly; faulty charger; dirty battery terminals; battery not seated correctly. | Ensure charger is firmly connected. Try a different compatible charger. Clean battery and device terminals. Re-insert battery, ensuring correct orientation. |
| Short operating time | Battery not fully charged; battery degradation over time; high power consumption by device. | Ensure battery is fully charged before use. If battery is old, consider replacement. Reduce device features that consume high power (e.g., backlight, volume). |
| Device does not power on | Battery not charged; battery not installed correctly; device issue. | Charge the battery. Re-install the battery, checking polarity. If problem persists, consult your device's manual or support. |
Specifications
| Model Number | CS-VL700F6 |
| Battery Type | Ni-MH (Nickel-Metal Hydride) |
| Capacity | 1200mAh |
| Voltage | 1.2V |
| Watt-Hours (Wh) | 1.44Wh |
| Dimensions | 66.78 x 16.7 x 5.96 mm (2.63 x 0.66 x 0.23 inches) |
| Weight | 50.0 g (1.76 oz) |
| Certifications | ISO9001, RoHS, CE, UN38.3, MSDS |
| Compatible Aiwa Models | AM-ST40, HS-PX787, AM-HX150, AM-NX1, AM-HX400, RP-BP61, HHF-AZ01T, AM-HX30, AM-HX70, AM-CL33, AM-HX200, HS-PX587, AM-HX50, AM-HX100, MHB 901, AM-HX300, AM-HX55, AM-F90 |
| Compatible Battery Part Number | MHB-901 |
Warranty and Support
BORNMIO products undergo strict quality inspection to ensure reliability. If you encounter any issues or have questions regarding your replacement battery, please contact BORNMIO customer support. We offer a full refund or a free replacement without any reason for products that do not meet expectations or have defects.
For support, please refer to the contact information provided with your purchase or visit the official BORNMIO website.