1. Introduction
This manual provides comprehensive instructions for the Lamomo 2m White Neon LED Strip Light. It covers product features, safety guidelines, installation procedures, operational instructions, maintenance tips, and troubleshooting steps. This LED strip is designed for various indoor and outdoor lighting applications, featuring 6000K white light, dimmable functionality, 12V low voltage operation, IP65 waterproof silicone construction, and a flexible design.
Package Contents:
- 1 x 2m White Neon LED Strip Light
- 1 x 12V 5A UL Listed AC Power Adapter
- 1 x Power Cord (with plug)
- 1 x Touch Dimmer Controller
- Mounting clips and screws
Image 1.1: The Lamomo 2m White Neon LED Strip Light, coiled to show its flexibility and uniform illumination.
2. Safety Information
- Power Supply: Only use the provided 12V power adapter. Using an incompatible power supply may damage the LED strip or pose a fire hazard.
- Water Resistance: The LED strip is IP65 waterproof, suitable for outdoor use and exposure to rain. However, the power adapter and dimmer controller are not waterproof and must be protected from moisture.
- Cutting: Only cut the LED strip at designated cutting marks (indicated by black lines or scissor icons). Cutting elsewhere will damage the circuit and render that section unusable.
- Installation: Ensure the power is disconnected before installation or maintenance. Avoid bending the strip sharply at angles less than 90 degrees to prevent damage.
- Heat: While low voltage, avoid covering the LED strip with materials that could trap heat, as this may reduce its lifespan.
- Children and Pets: Keep the product and its components out of reach of children and pets.
3. Setup and Installation
Follow these steps to properly install your Lamomo Neon LED Strip Light:
- Plan Your Layout: Determine the desired path for your LED strip. The strip is highly flexible and can be bent to create various shapes and follow contours.
Image 3.1: The silicone material allows for high flexibility, enabling concave, convex, linear, and 90-degree installations without damage.
- Measure and Cut (if necessary): If a shorter length is required, measure carefully and cut the LED strip only at the designated cutting marks. These marks are typically indicated by a black line or a scissor icon every 2.5cm.
Image 3.2: Detail of the LED strip highlighting the cuttable sections (every 2.5cm) and its IP65 waterproof construction.
- Mount the Strip: Use the provided mounting clips and screws to secure the LED strip in place. Ensure the clips are evenly spaced to provide stable support.
Image 3.3: An example of the LED strip installed around a corner, showcasing its ability to bend and conform to various surfaces.
- Connect the Dimmer Controller: Plug the LED strip's connector into the touch dimmer controller. Ensure the connection is secure.
- Connect the Power Adapter: Plug the power cord into the 12V power adapter, then connect the power adapter to the dimmer controller.
- Power On: Plug the power cord into a standard electrical outlet.
4. Operation
The Lamomo LED strip is operated using the included touch dimmer controller.
Image 4.1: The touch dimmer controller allows for easy adjustment of light intensity. The image shows the dimmer switch and instructions for use.
- Turn On/Off: Briefly touch the power icon on the dimmer switch to turn the LED strip on or off.
- Adjust Brightness: Press and hold the power icon on the dimmer switch for 2-3 seconds to adjust the brightness. The light will gradually brighten or darken. Release your finger when the desired brightness level (10% to 100%) is reached.
5. Maintenance
- Cleaning: Ensure the LED strip is powered off and unplugged before cleaning. Wipe the silicone surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Power Adapter and Dimmer: Keep the power adapter and dimmer controller dry and away from direct moisture.
- Inspection: Periodically inspect the LED strip and connections for any signs of damage or wear. If any damage is found, discontinue use and contact customer support.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strip does not light up. |
|
|
| Light flickers or is inconsistent. |
|
|
| Dimmer not responding. |
|
|
7. Specifications
Image 7.1: Visual representation of the product's key specifications and included components.
| Feature | Detail |
|---|---|
| Brand | Lamomo |
| Model Number | SA-CW-DE-2M |
| Type | LED Strip Lights |
| Color | White |
| Color Temperature | 6000K |
| Length | 2 meters (6.56 ft) |
| Operating Voltage | 12V |
| Working Current | ≤6A / 2 meters |
| Power | 11 Watts |
| LED Type | SMD 2835 |
| LED Quantity per Meter | 100 pieces |
| Material | Silicone |
| Waterproof Rating | IP65 (Strip only) |
| Special Features | Dimmable, Waterproof, Cuttable, Flexible |
| Lumen Output | 30-35 LM (per LED, implied) |
| Illumination Range | 180° |
| Certification | CE |
Image 7.2: EU Energy Label for the Lamomo LED strip, indicating an energy efficiency class of F and 35 kWh/1000h consumption. More details can be found at eprel.ec.europa.eu/qr/1513482.
8. Warranty and Support
This Lamomo LED Strip Light is backed by a two-year warranty from the date of purchase, covering manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
For technical support, warranty service, or any questions regarding your product, please contact Lamomo customer service through the retailer where the product was purchased.
