Introduction
Thank you for choosing the BoxWave ClearTouch Crystal Screen Protector for your Pax E600 Mini. This high-quality screen protector is designed to shield your device's display from scratches, dust, and daily wear, while preserving its original clarity and vibrant colors. With its precision-cut design and easy application, you can ensure your device's screen remains pristine.
Image: The ClearTouch Crystal Screen Protector seamlessly applied to a device, demonstrating its transparent and protective qualities.
Package Contents
Your BoxWave ClearTouch Crystal Screen Protector package includes the following items:
- Two (2) BoxWave ClearTouch Crystal Screen Protectors
- One (1) ClearTouch Applicator Card
- One (1) Microfiber Cleaning Cloth
- One (1) Dust Removing Sticker
Image: A visual representation of the package contents, showing the two screen protectors, applicator card, and microfiber cleaning cloth.
Image: A detailed view of the applicator card, microfiber cleaning cloth, and dust removing sticker, essential tools for installation.
Setup and Installation
Follow these steps carefully to ensure a bubble-free and perfect installation of your screen protector:
Preparation
- Clean Your Device Screen: Use the provided microfiber cleaning cloth to thoroughly wipe down the screen of your Pax E600 Mini. Ensure there are no dust particles, smudges, or fingerprints. For stubborn marks, a small amount of screen cleaner can be used, followed by a dry wipe with the microfiber cloth.
- Remove Dust: Use the dust removing sticker to lift any remaining dust particles from the screen. Lightly dab the sticker across the entire screen surface.
- Work in a Clean Environment: Choose a dust-free area for installation to minimize the chance of particles getting trapped under the protector.
Application Steps
- Peel Back Layer 1: Carefully peel back a small portion of the protective film labeled 'Layer 1' from one end of the screen protector. Avoid touching the adhesive side.
- Align the Protector: Align the exposed adhesive edge of the screen protector with one edge of your device's screen. Ensure precise alignment with the device's cutouts (if any) and edges.
- Apply Gradually: Slowly and steadily lower the rest of the screen protector onto the device's screen, peeling back 'Layer 1' as you go. Use the ClearTouch Applicator Card to gently push out any air bubbles as you apply, working from the applied edge towards the opposite end.
- Remove Remaining Bubbles: If any small bubbles remain, use the applicator card to push them towards the nearest edge. Apply firm, even pressure.
- Peel Back Layer 2: Once the screen protector is fully adhered and most bubbles are removed, carefully peel off the top protective film labeled 'Layer 2'.
- Final Adhesion: The special low-tack adhesive may take a little time to fully adhere around the edges. Any small air gaps around the edges will typically clear out within approximately 2 days of regular use.
Operation
Once installed, the BoxWave ClearTouch Crystal Screen Protector operates seamlessly with your Pax E600 Mini. It is designed to maintain full touch screen sensitivity and display clarity, allowing you to use your device as normal without any interference. The protector provides an invisible layer of defense, ensuring your screen remains responsive and visually vibrant.
Image: The screen protector's high definition clarity is demonstrated by a vibrant image viewed through it, showcasing 99% visual transparency.
Maintenance
To keep your BoxWave ClearTouch Crystal Screen Protector clean and clear, simply wipe it gently with the provided microfiber cleaning cloth. For more persistent smudges or fingerprints, you may slightly dampen the cloth with water or a mild, screen-safe cleaning solution. Avoid using harsh chemicals or abrasive materials, as these can damage the protector's surface.
Troubleshooting
Air Bubbles After Installation
Small air bubbles are common immediately after installation. Most small bubbles will dissipate on their own within 24-48 hours as the adhesive fully cures. For larger bubbles, you can try gently lifting the nearest edge of the screen protector and reapplying it, using the applicator card to push the air out as you lay it back down. Ensure no dust particles are trapped under the bubble.
Edges Not Sticking
If the edges of the screen protector are not fully adhering, ensure the screen was thoroughly cleaned and free of dust or oils before application. Apply gentle, consistent pressure along the edges with the applicator card. As mentioned, the low-tack adhesive may take up to 2 days to fully bond, and edge gaps often resolve during this period with regular use.
Specifications
| Feature | Detail |
|---|---|
| Brand | BoxWave |
| Material | Polyethylene Terephthalate (PET) |
| Item Hardness | 9H |
| Special Feature | Scratch Resistant |
| Unit Count | 2.0 Count |
| Screen Surface Description | Glossy |
| Clarity | 99% Visual Transparency |
| Item Weight | 1.6 ounces |
| Country of Origin | China |
Warranty and Support
BoxWave products are designed for quality and durability. For specific warranty information or technical support regarding your ClearTouch Crystal Screen Protector, please refer to the packaging or visit the official BoxWave website. Our customer service team is available to assist with any questions or concerns you may have.
