Introduction
This manual provides essential instructions for the safe installation, operation, and maintenance of your LITFAD Minimalist LED Vanity Sconce Light. Please read this manual thoroughly before installation and retain it for future reference.
Important Safety Instructions
WARNING: To reduce the risk of fire, electric shock, or personal injury, always follow these safety precautions.
- For a safe and secure installation, ensure that the electrical box to which this fixture will be mounted is properly attached to a structural member of the building.
- All wires are connected. When unpacking, be careful not to pull with wires as a bad connection may result.
- Do not connect electricity until your fixture is fully assembled.
- To reduce the risk of fire, electrical shock, or personal injury, always turn off and unplug the fixture and allow it to cool prior to replacing the light bulb (not applicable as LED is integrated).
- Do not touch the light when the fixture is turned on or look directly at the lit light. Keep flammable materials away from the lit light.
- Installation should be performed by a qualified electrician.
Package Contents
Verify that all components are present and undamaged before beginning installation. If any parts are missing or damaged, contact customer support.
- LITFAD Minimalist LED Vanity Sconce Light (1 unit)
- Mounting Hardware (screws, wire nuts, etc.)
- User Manual (this document)
Setup and Installation
Follow these steps carefully for proper installation. Ensure power is turned off at the circuit breaker before starting.
- Prepare the Installation Area: Turn off power at the main circuit breaker. Ensure the mounting surface is clean, dry, and structurally sound.
- Identify Components: Unpack all components and identify the light fixture, mounting bracket, and hardware.
- Mount the Bracket: Secure the mounting bracket to the electrical junction box on the wall using the provided screws. Ensure it is firmly attached.
- Connect Wiring: Connect the fixture's wires to the corresponding household wires (black to black, white to white, ground to ground) using the provided wire nuts. Ensure all connections are secure.
- Attach the Fixture: Carefully align the light fixture with the mounting bracket and secure it in place using the provided screws. Ensure the fixture is flush against the wall.
- Restore Power: Once the fixture is securely installed, restore power at the circuit breaker.
Figure 1: Product Dimensions. The light measures approximately 15.5 inches (39.37 cm) in width and 4 inches (10.16 cm) in height.
Figure 2: Top and Bottom View. This image illustrates the construction of the light, highlighting the wood and acrylic materials from different angles.
Operating Instructions
The LITFAD Minimalist LED Vanity Sconce Light features integrated LED lighting with 3 color temperature options and touch control.
- Power On/Off: Gently touch the designated area on the fixture to turn the light on or off.
- Change Color Temperature: With the light on, touch the designated area again to cycle through the available color temperatures (e.g., warm white, neutral white, cool white).
Figure 3: Illuminated Sconce Light. The light fixture is shown fully illuminated, demonstrating its operational state.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your light fixture.
- Cleaning: Disconnect power before cleaning. Use a soft, dry cloth to wipe the fixture. Do not use abrasive cleaners or solvents, as they may damage the finish or acrylic.
- LED Care: The LED light source is integrated and not user-replaceable. Do not attempt to disassemble the LED module.
Troubleshooting
If you encounter issues with your light fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power supply Loose wiring connection Faulty switch | Check circuit breaker and wall switch Verify all wire connections are secure (ensure power is off) Test the switch for functionality |
| Light flickers | Loose wiring Incompatible dimmer (if applicable) | Check wiring connections (ensure power is off) Ensure the light is not connected to an incompatible dimmer switch |
| Color temperature does not change | Incorrect touch operation Internal fault | Ensure you are touching the correct area for color change Contact customer support if the issue persists |
Specifications
| Feature | Detail |
|---|---|
| Model Number | LT766582AS |
| Fixture Width | 16 inches (40 cm) |
| Fixture Height | 4 inches (10 cm) |
| Material | Wood + Acrylic |
| Light Source | Integrated LED |
| Wattage | 14W |
| Voltage | AC110-120V |
| Control Method | Touch |
| Color Temperature | 3 Colors Light (Adjustable) |
| Indoor/Outdoor Usage | Indoor |
| Mounting Type | Wall Mount |
Warranty
This LITFAD LED Vanity Sconce Light comes with a 2-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, misuse, accidents, or unauthorized modifications.
Customer Support
If you have any questions, suggestions, or require assistance with your LITFAD product, please do not hesitate to contact us. Our online service is available 24 hours a day, 7 days a week.
For support, please visit the LITFAD Store on Amazon or refer to the contact information provided with your purchase.