Introduction
The T-Fal Ultraglide Steam Iron FV5841U0 is designed to make ironing ultra-smooth and efficient. Featuring a patented Durilium AirGlide soleplate, this iron effortlessly glides across garments, offering superior scratch resistance and long-lasting performance. With 1800 watts of power, it ensures fast heat-up and powerful steam output for effective wrinkle removal.
This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your T-Fal Ultraglide Steam Iron.
Important Safety Instructions
When using your iron, basic safety precautions should always be followed:
- Read all instructions before using the iron.
- Use the iron only for its intended use.
- To protect against a risk of electric shock, do not immerse the iron in water or other liquids.
- Always turn the iron OFF before plugging or unplugging from the outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
- Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
- The iron should always be turned to "Min" before plugging or unplugging from outlet.
- Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron; take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
- Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.
- Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
- The iron must be used and rested on a stable surface.
- When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
- The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.
Auto-Off Feature: For enhanced safety, the iron is equipped with an auto-off function:
- Shuts off in 30 seconds if left horizontally or on its side.
- Shuts off in 8 minutes if left upright.
Product Components
Overall View: The T-Fal Ultraglide Steam Iron FV5841U0 in Teal and Black.
Key Features Diagram: Illustrates the iron's main features including Eco-friendly mode, 100g/min steam burst, cold spray control, steam control, built-in spray for deep creases, precision tip, and ultra scratch-resistant Durilium AirGlide soleplate.
Durilium AirGlide Soleplate: Patented soleplate providing the speed of nonstick with the durability of stainless steel, ensuring extremely scratch-resistant performance.
Anti-Drip System: Prevents water drips and white marks on your garments during ironing. Features a built-in cleaning system to capture mineral build-up.
Worry-Free Auto-Off: The iron automatically shuts off after 30 seconds horizontally or on its side, and after 8 minutes when left upright, enhancing safety.
Vertical Steaming: Allows for de-wrinkling garments and refreshing fabrics without the need for an ironing board.
Setup
Before First Use:
It is normal to find condensation or water droplets inside the water tank upon unboxing. This is due to the manufacturer's pre-testing process to ensure proper functionality.
Filling the Water Tank:
- Ensure the iron is unplugged from the power outlet.
- Set the steam control to the 'Dry Ironing' position (no steam).
- Open the water filling inlet cover located on the top of the iron.
- Fill the water tank with tap water up to the 'MAX' level indicator. Do not overfill.
- Close the water filling inlet cover securely.
Note: Tap water is recommended for this iron. Distilled water is not necessary and may not provide optimal performance.
Operating Instructions
Powering On and Temperature Selection:
- Plug the iron into a suitable power outlet. The indicator light will illuminate.
- Turn the temperature dial to select the desired heat setting based on the fabric type. Settings include:
- Delicate (low heat)
- Wool
- Cotton
- Max (high heat)
- Eco Mode (uses 20% less energy)
- Allow the iron to heat up until the indicator light turns off, signaling that the selected temperature has been reached.
Steam Ironing:
- Ensure the water tank is filled.
- Set the temperature dial to a steam-compatible setting (typically Wool, Cotton, or Max).
- Adjust the steam control slider to the desired steam output (continuous steam up to 30 g/min).
- For stubborn creases, press the steam boost button to deliver an extra burst of steam (up to 100 g/min).
Vertical Steaming:
- Hang the garment on a hanger.
- Hold the iron in a vertical position, close to the fabric but not touching it.
- Press the steam boost button to release steam and remove wrinkles.
Spray Function:
- Press the spray button to lightly mist the fabric with water, which helps in smoothing out tough wrinkles.
Precision Tip:
- The pointed tip of the soleplate allows for easy access to difficult areas such as collars, cuffs, and around buttons.
Maintenance and Cleaning
Built-in Cleaning System (Anti-Calc):
The iron features a built-in cleaning system to prevent mineral build-up and prolong its lifespan. Refer to the full user manual for detailed calc cleaning instructions, typically recommended monthly.
Emptying the Water Tank:
- After each use, unplug the iron and allow it to cool completely.
- Open the water filling inlet cover and invert the iron over a sink to drain any remaining water.
- Close the cover and store the iron upright.
Soleplate Cleaning:
- To clean the soleplate, use a damp cloth and a non-abrasive cleaner.
- Do not use abrasive scouring pads or harsh chemicals, as these can damage the Durilium AirGlide coating.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Iron does not heat up. | Not plugged in; power outlet issue; auto-off activated. | Check power cord connection; test outlet with another appliance; move iron to reactivate. |
| No steam or insufficient steam. | Water tank empty; temperature too low for steam; steam control set to 'Dry Ironing'. | Fill water tank; set temperature to steam-compatible range (Wool, Cotton, Max); adjust steam control. |
| Water leaking from soleplate. | Temperature too low for steam; iron overfilled; calc build-up. | Increase temperature; do not overfill; perform calc cleaning. |
| White marks on clothes. | Mineral deposits from water. | Perform calc cleaning regularly. |
If the problem persists after attempting these solutions, please refer to the full user manual or contact customer support.
Specifications
- Brand: Tefal
- Model Name: Ultraglide
- Item Model Number: 83430
- Power: 1800 Watts
- Soleplate Material: Durilium AirGlide (Aluminum)
- Special Features: Steam Boost Function, Vertical Steaming, Anti-Drip, Auto-Off
- Color: Teal, Black
- Product Dimensions: 12"L x 6"W
- Item Weight: 3.63 pounds
- UPC: 023108834308
- Country of Origin: China
Warranty and Support
Warranty: This T-Fal Ultraglide Steam Iron FV5841U0 comes with a 1 Year Limited Warranty.
For detailed warranty terms, service, or additional support, please refer to the official T-Fal User Manual PDF available online or contact T-Fal customer service.
Official User Manual (PDF): Download Here
