Important Safety Information
Before beginning any installation or maintenance, please read and understand all safety instructions. Failure to follow these instructions could result in property damage, personal injury, or death.
- Always disconnect power to the washer before servicing.
- Turn off the water supply to the washer before disconnecting any water lines.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- Ensure all connections are secure and leak-free before restoring power and water.
- If you are unsure about any step, consult a qualified technician.
Product Overview
The Owigift Washer Water Inlet Valve is a replacement component designed to control the flow of hot and cold water into your washing machine. This specific valve features a durable plastic body, two ports for water connections, and a 1/2 inch NPT inlet. It is an aftermarket replacement part compatible with various washer brands and models.
Image 1: The Owigift Washer Water Inlet Valve. This image shows the blue plastic body of the valve with two threaded inlets for water hoses and two black solenoids with electrical terminals. A black outlet nozzle is visible on the right side.
Compatibility
This water inlet valve is an aftermarket replacement part compatible with a range of washers from brands such as Whirlpool, Kenmore, Maytag, and Inglis. Please verify your washer's model number against the list below to ensure compatibility.
Partial list of compatible Kenmore models:
- 110.25852400
- 110.25854400
- 110.25862400
- 110.25864400
- 110.26152500
- 110.26852500
- 110.26852501
- 110.26852502
- 110.26852503
- 110.26852504
- 110.26862500
- 110.26862501
- 110.26862502
- 110.26862503
- 110.26882500
- 110.26882501
- 110.26882502
- 110.26882503
- 110.26884500
- 110.26884501
- 110.26884502
- 110.26884503
- 110.26922500
- 110.26922501
- 110.26922502
- 110.26922503
- 110.26924500
- 110.26924501
- 110.26924502
- 110.26924503
- 110.26942500
- 110.26942501
- 110.26942502
- 110.26942503
- 110.26944500
- 110.26944501
- 110.26944502
- 110.26944503
- 110.26962500
- 110.26962501
- 110.26962502
- 110.26962503
- 110.26964500
- 110.26964501
- 110.26964502
- 110.26964503
- 110.26966500
- 110.27222600
- 110.27224600
- 110.27721600
- 110.27731600
- 110.27741600
- 110.27751700
- 110.27761700
- 110.27782700
- 110.27831600
- 110.27841600
- 110.27871600
- 110.27872600
- 110.27874600
- 110.28222700
- 110.28522701
- 110.28532701
- 110.28622701
- 110.28632701
- 110.28692701
- 110.28722700
- 110.28732700
- 110.28752700
- 110.28762700
- 110.28782700
- 110.28832700
- 110.28837700
- 110.28842700
- 110.28847700
- 110.29422800
- 110.29432800
- 110.29442800
- 110.29522800
- 110.29532800
- 110.29592800
- 110.29622800
- 110.29632800
- 110.29672800
- 110.29682800
- 110.29692800
- 110.29722800
- 110.29727800
- 110.29732800
- 110.29737800
Setup and Installation
This section provides general instructions for replacing a washer water inlet valve. Specific steps may vary slightly depending on your washer model. Always refer to your washer's service manual for detailed instructions.
- Preparation: Gather necessary tools, which typically include screwdrivers, pliers, and a bucket or towels to catch residual water. Ensure you have the correct replacement valve.
- Disconnect Power: Locate your washer's power cord and unplug it from the electrical outlet. This is a critical safety step.
- Turn Off Water Supply: Locate the hot and cold water faucets connected to your washer and turn them off completely.
- Disconnect Water Hoses: Place a bucket behind the washer to catch any water. Disconnect the hot and cold water hoses from the back of the washer.
- Access the Valve: Depending on your washer model, you may need to remove the back panel or top panel to access the water inlet valve. Use appropriate tools to remove screws or clips.
- Disconnect Electrical Connections: Carefully disconnect the electrical wiring harnesses from the solenoids on the old water inlet valve. Note their positions for reassembly.
- Remove Old Valve: Disconnect the water outlet hose from the valve. Unmount the old valve from its housing. This may involve removing screws or releasing clips.
- Install New Valve: Position the new Owigift water inlet valve in the same location as the old one. Secure it with screws or clips.
- Reconnect Connections: Reconnect the water outlet hose to the new valve. Reattach the electrical wiring harnesses to the corresponding solenoids on the new valve. Ensure connections are firm.
- Reconnect Water Hoses: Reattach the hot and cold water hoses to the threaded inlets on the new valve. Hand-tighten, then use pliers to tighten an additional quarter turn. Do not overtighten.
- Restore Water Supply: Slowly turn on the hot and cold water faucets. Check for any leaks at the hose connections. Tighten if necessary.
- Restore Power and Test: Reinstall any panels removed. Plug the washer's power cord back into the electrical outlet. Run a short wash cycle to test the new valve and check for proper water fill and any leaks.
Operating Instructions
As a replacement part, the Owigift Washer Water Inlet Valve operates automatically as part of your washing machine's normal cycle. Once installed correctly, it will open and close as directed by the washer's control board to allow the appropriate amount of hot and cold water into the tub for each wash cycle.
- Ensure water supply is always on when operating the washer.
- Select desired wash cycle and temperature settings on your washer's control panel.
- The valve will activate to fill the tub with water according to your selections.
Maintenance
Proper maintenance can extend the life of your water inlet valve and prevent future issues.
- Inspect Hoses: Periodically check the hot and cold water inlet hoses for cracks, bulges, or leaks. Replace them every 3-5 years, or sooner if damage is observed.
- Clean Inlet Screens: Most water inlet valves have small screens at the hose connections to filter out sediment. If water flow is reduced, turn off water and power, disconnect hoses, and clean these screens.
- Prevent Freezing: If your washer is in an unheated area, ensure water lines are drained or protected from freezing temperatures to prevent damage to the valve.
Troubleshooting
If you experience issues after installing the new water inlet valve, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Washer not filling with water | Water supply off, clogged inlet screens, faulty electrical connection to valve. | Ensure water faucets are fully open. Clean inlet screens. Check electrical connections to valve solenoids. |
| Washer filling slowly | Clogged inlet screens, low water pressure. | Clean inlet screens. Check household water pressure. |
| Water leaking from valve area | Loose hose connections, cracked valve housing, faulty seals. | Tighten hose connections. Inspect valve for cracks. Ensure seals are properly seated. |
| Washer fills with wrong temperature water | Hot and cold hoses reversed, faulty solenoid. | Verify hot and cold hoses are connected to the correct inlets. If issue persists, a solenoid may be faulty. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Owigift |
| Part Type | Washer Water Inlet Valve |
| Material | Plastic |
| Valve Type | Globe Valve |
| Number of Ports | 2 |
| Inlet Connection Type | 1/2 inch NPT |
| UPC | 718997260603 |
| GTIN | 718997260603 |
Warranty Information
As an aftermarket replacement part, specific warranty details may vary. Please refer to the seller or manufacturer's policy at the time of purchase for information regarding warranty coverage, duration, and claims process. Keep your purchase receipt as proof of purchase.
Support
For further assistance, compatibility questions, or troubleshooting not covered in this manual, please contact the seller directly through the platform where the product was purchased. They can provide specific guidance related to your purchase.
If you are unsure about the compatibility, please contact us for advice. We aim to solve your problem within 24 hours.