Sleek Socket Ultra-Thin Outlet Concealer

1. Introduction

The Sleek Socket Ultra-Thin Outlet Concealer is designed to provide a discreet and efficient solution for managing electrical cords and outlets. This product converts a standard duplex wall outlet into a concealed power source with two 8-foot flat extension cords, each terminating in a 3-outlet power strip. It is ideal for situations where furniture needs to sit flush against a wall, or where a clean, clutter-free appearance is desired.

2. Safety Information

• This product is certified to UL Standard 817 (Safety Cord Sets and Power-Supply Cords) and CSA C22.2 #21.
• Do not exceed the maximum electrical rating: 13 Amps, 125 Volts, 1625 Watts.
• Ensure the product is fully inserted into a duplex outlet.
• Avoid covering the Sleek Socket or its cords with rugs, furniture, or other materials that could impede ventilation or cause overheating.
• Keep cords away from heat sources, water, and sharp objects.
• This product is designed for indoor use only.

3. Package Contents

• 1 x Sleek Socket Ultra-Thin Outlet Concealer unit
• 2 x 8-foot flat extension cords, each with a 3-outlet power strip
• Adhesive cord clips and double-sided adhesive strips for cord management

Image 1: Components of the Sleek Socket Ultra-Thin Outlet Concealer.

4. Setup and Installation

No tools are required for installation.

1. Check Outlet Compatibility: Ensure your duplex wall outlet has a round ground pin located below the two flat pins. The Sleek Socket is designed for this standard pin orientation.


Image 2: Compatibility diagram for standard duplex outlets.

2. Insert the Sleek Socket: Firmly plug the Sleek Socket unit into the top receptacle of your standard duplex wall outlet. It should sit flush against the wall.
3. Route the Cords: The unit features two 8-foot flat extension cords. Route these cords along the baseboard or wall to your desired locations.
4. Secure Cords with Clips: Use the provided adhesive cord clips and double-sided adhesive strips to neatly secure the flat cords to the wall. This helps eliminate clutter and potential tripping hazards.


Image 3: Example of Sleek Socket installation behind furniture.

5. Operating Instructions

Once installed, the Sleek Socket provides six additional outlets (three on each 8-foot cord) for powering your devices. Simply plug your appliances, lamps, or other electronics into the 3-outlet power strips at the end of each flat cord.

• The ultra-thin design allows furniture to sit closer to the wall, maximizing space.
• The flat cords are up to 90% thinner than traditional plugs and cords, blending seamlessly with your decor.

6. Maintenance

• Regularly inspect the cords and power strips for any signs of damage, fraying, or overheating. Discontinue use if any damage is observed.
• Keep the unit and cords clean by wiping with a dry cloth. Do not use liquid cleaners.
• Ensure the adhesive clips remain securely attached to prevent cords from becoming loose.

7. Troubleshooting

• Issue: Sleek Socket does not fit into the wall outlet.
  Solution: Verify that your wall outlet is a standard duplex type with the round ground pin located below the flat pins. Refer to Image 2 for compatibility.
• Issue: Devices are not receiving power.
  Solution: Ensure the Sleek Socket is fully inserted into the wall outlet. Check that the total power consumption of connected devices does not exceed 1625 Watts.
• Issue: Cords are not staying securely attached to the wall.
  Solution: Reapply or replace the adhesive cord clips and strips. Ensure the wall surface is clean and dry before application.

8. Specifications

9. Warranty and Support

Sleek Socket guarantees that all products are sold in 100% new condition. Any appearance of scuffed or damaged product may occur from the shipping process. We stand behind all of our products and will replace products damaged during the shipment process. For support or replacement inquiries, please contact the manufacturer, Socket Solutions, LLC.