ARB Base Rack Mount Kit 17913010 Instruction Manual

1. Product Overview

The ARB Base Rack Mount Kit (Model 17913010) is designed to securely attach an ARB BASE Rack (specifically compatible with PN 1770030 and 1770020) to your vehicle's roof. This kit ensures a robust and stable platform for carrying various loads, integrating seamlessly with your vehicle's existing factory mounting points. It also includes a wind deflector to reduce noise and drag.

Key Features:

• Designed for use with ARB BASE Rack models PN 1770030 and PN 1770020.
• Mount feet attach directly to original equipment (OE) factory points on the vehicle roof.
• Includes support plates specifically designed for the BASE Rack extrusion.
• Comes with a wind deflector to optimize aerodynamics and reduce noise.
• Compatible with the fitment of ARB Roof Rack LED light bar PN 1780500.

Image 1.1: ARB Base Rack Mount Kit installed on a vehicle, showcasing its low-profile design.

2. Kit Contents

Before beginning installation, please verify that all components listed below are present and undamaged. If any parts are missing or damaged, contact your ARB dealer immediately.

Image 2.1: Overview of all components included in the ARB Base Rack Mount Kit.

• Mounting Rails (2)
• Mounting Feet/Brackets (various quantities, specific to vehicle model)
• Support Plates
• Wind Deflector
• Fasteners (bolts, nuts, washers, etc.)
• Installation Hardware (e.g., rubber gaskets, spacers)

Note: Specific quantities and types of mounting feet/brackets may vary based on the vehicle application. Refer to the detailed parts list provided with your physical kit.

3. Setup and Installation

Installation of the ARB Base Rack Mount Kit requires mechanical aptitude and basic tools. It is recommended that installation be performed by a qualified professional. Always refer to the specific vehicle-fitment instructions included with your kit for detailed steps and torque specifications.

3.1. Pre-Installation Checks

1. Read Instructions: Thoroughly read all instructions before beginning.
2. Verify Components: Ensure all parts listed in Section 2 are present.
3. Vehicle Preparation: Clean the vehicle's roof area where the rack will be mounted. Remove any existing roof rack components if necessary.
4. Tools Required: Gather all necessary tools (e.g., wrenches, sockets, torque wrench, measuring tape, sealant).

3.2. General Installation Steps (Consult Vehicle-Specific Guide for Details)

1. Identify Mounting Points: Locate the factory mounting points on your vehicle's roof. These are typically covered by trim or caps.
2. Install Mounting Feet: Attach the vehicle-specific mounting feet to the factory points using the provided hardware. Ensure proper orientation and hand-tighten fasteners initially.
3. Position Mounting Rails: Place the long mounting rails onto the installed mounting feet. The rails should align with the BASE Rack extrusion.
4. Attach Support Plates: Secure the support plates to the mounting rails and the BASE Rack extrusion as per the specific instructions.
5. Install Wind Deflector: Attach the wind deflector to the front of the BASE Rack, ensuring it is centered and securely fastened.
6. Final Tightening: Once all components are correctly aligned and positioned, progressively tighten all fasteners to the torque specifications provided in your vehicle-specific instructions. Do not overtighten.
7. Sealant Application: If specified, apply appropriate sealant around mounting points to prevent water ingress.

Image 3.1: The main mounting rails, which form the base for the ARB BASE Rack.

Safety Warning: Improper installation can lead to product failure, vehicle damage, or serious injury. If you are unsure about any step, seek professional assistance.

4. Operating Instructions

Once the ARB Base Rack Mount Kit and BASE Rack are installed, it provides a versatile platform for carrying gear. Adhere to the following guidelines for safe operation:

• Weight Capacity: Never exceed the maximum load capacity specified for your ARB BASE Rack and your vehicle's roof. Consult your vehicle's owner's manual for roof load limits.
• Load Distribution: Distribute weight evenly across the rack. Place heavier items as low and as close to the center of the vehicle as possible.
• Secure Loads: Always secure all items to the rack using appropriate tie-downs, straps, or cargo nets. Check load security before and during travel.
• Vehicle Dynamics: Be aware that carrying loads on the roof can affect your vehicle's handling, braking, and fuel economy. Adjust driving style accordingly, especially when cornering or in windy conditions.
• Height Clearance: Remember that the overall height of your vehicle will increase with the rack and any loaded items. Be mindful of low clearances (e.g., garages, carports, drive-thrus).

Image 4.1: Side view of the ARB Base Rack system on a vehicle, ready for use.

5. Maintenance

Regular maintenance ensures the longevity and safe operation of your ARB Base Rack Mount Kit.

• Periodic Inspection: Regularly inspect all mounting hardware, bolts, and connections for tightness. Re-tighten to specified torque values if necessary, especially after the first 50 miles of use and periodically thereafter.
• Check for Damage: Inspect the rack and mounting components for any signs of wear, corrosion, cracks, or damage. Replace any damaged parts immediately.
• Cleaning: Clean the rack and mounting kit with mild soap and water. Avoid abrasive cleaners or solvents that could damage the finish.
• Wind Deflector: Ensure the wind deflector is free from debris and securely attached.

6. Troubleshooting

This section addresses common issues you might encounter with your ARB Base Rack Mount Kit.

• Excessive Wind Noise:
  • Ensure the wind deflector is correctly installed and positioned.
  • Check for any loose components on the rack or mount kit.
  • Verify that no accessories are creating unusual airflow.
• Loose Rack:
  • Inspect all mounting bolts and fasteners. Re-tighten to the specified torque.
  • Check for any deformation or damage to the mounting feet or vehicle's factory points.
• Water Leaks from Mounting Points:
  • Ensure that any required sealant was applied correctly during installation.
  • Inspect rubber gaskets or seals for damage or improper seating.

If you encounter issues not covered here or require further assistance, please contact ARB customer support or your authorized dealer.

7. Specifications

8. Warranty and Support

For information regarding product warranty, please refer to the warranty documentation included with your purchase or visit the official ARB website. For technical support, installation queries, or to report any issues, please contact your authorized ARB dealer or ARB customer service directly.

ARB Official Website: www.arb.com.au

ARB Store on Amazon: Visit the ARB Store