REBEL RB-0003 3-in-1 Detector User Manual
Model: RB-0003
1. Introduction
Thank you for choosing the REBEL RB-0003 3-in-1 Detector. This device is designed to assist you in safely locating metal, wood, and live AC cables hidden within walls, ceilings, and floors. Please read this manual thoroughly before operating the device to ensure safe and effective use.
The RB-0003 is an essential tool for DIY enthusiasts and professionals, providing accurate detection to prevent damage during drilling, cutting, or renovation projects.
2. Safety Information
- Always exercise caution when working near detected objects.
- Do not rely solely on the detector for safety. Always verify findings with other methods if possible, especially when dealing with electrical wires.
- Keep the device dry and clean. Do not expose it to moisture or extreme temperatures.
- Do not attempt to open or modify the device. Repairs should only be performed by qualified personnel.
- Remove batteries if the device will not be used for an extended period.
3. Product Overview
Familiarize yourself with the components of your REBEL RB-0003 detector:
Figure 1: Front view of the REBEL RB-0003 Detector in packaging. The device features a large display and a 'SELECT' button for mode switching.
Figure 2: Rear view of the REBEL RB-0003 Detector. This view shows the battery compartment and the product information label.
- Display Screen: Shows detection mode, signal strength, and low battery indicator. (Display size: 51 x 25 mm)
- SELECT Button: Used to switch between detection modes (Metal, Wood, AC Cable).
- Sensor Area: Located on the back of the device, this area must be flush against the surface for accurate readings.
- Battery Compartment: Located on the back, for battery installation.
4. Setup
4.1. Battery Installation
- Open the battery compartment cover on the back of the device (refer to Figure 2).
- Insert the required batteries, ensuring correct polarity (+/-). The device requires batteries for operation.
- Close the battery compartment cover securely.
The device features a low battery indicator on the display. Replace batteries promptly when this indicator appears to ensure accurate readings.
5. Operating Instructions
5.1. General Operation
- Press the power button (if available, otherwise the SELECT button usually powers it on) to turn on the device.
- Press the SELECT button to cycle through the detection modes: Metal, Wood, and AC Cable. The selected mode will be indicated on the display.
- Place the detector flat against the surface you wish to scan. Ensure the sensor area is in full contact.
- Slowly slide the detector across the surface. The display will show signal strength and indicate when an object is detected.
5.2. Metal Detection
In Metal detection mode, the RB-0003 can detect metal parts in walls up to a depth of 30 mm.
- Select the Metal detection mode.
- Move the device slowly across the surface. The display will show increasing bars as it approaches a metal object.
- A distinct audio alert or visual indicator will confirm the presence of metal.
5.3. Wood Detection
The device can detect wooden profiles with a maximum dimension of 30 x 30 mm at a depth of 18 mm.
- Switch to Wood detection mode.
- Scan the wall slowly. The detector will indicate the edges and center of wooden studs or beams.
- Mark the detected areas for reference.
5.4. AC Cable Detection
The RB-0003 is capable of detecting live AC 90-250V cables.
- Select the AC Cable detection mode.
- Move the detector slowly over the area. The device will emit a warning and display an icon when live AC voltage is detected.
- Caution: Always assume wires are live until confirmed otherwise by a qualified electrician.
6. Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the detector in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
- Battery Replacement: Replace batteries when the low battery indicator appears on the display. Use only the specified battery type.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not turn on. | Dead or incorrectly installed batteries. | Check battery polarity or replace batteries. |
| Inaccurate readings. | Low battery, improper contact with surface, or environmental interference. | Replace batteries. Ensure the device is flat against the surface. Avoid scanning near strong electromagnetic fields. |
| No detection in AC mode. | Wires are not live, or too deep. | Ensure power is on to the circuit. Scan slowly and thoroughly. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | RB-0003 (MIE-RB-0003) |
| Brand | REBEL |
| Metal Detection Depth | Up to 30 mm |
| Wood Detection Depth | Up to 18 mm (for 30x30 mm profiles) |
| AC Cable Detection | 90-250V |
| Display Size | 51 x 25 mm |
| Low Battery Indicator | Yes |
| Power Source | Battery Powered |
| Product Dimensions | 15.5 x 5.4 x 2.7 cm |
| Item Weight | 157 Grams |
| International Protection Rating | IP66 |
9. Warranty and Support
REBEL products are manufactured to high-quality standards and are guaranteed against manufacturing defects. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official REBEL website.
For technical support, troubleshooting assistance, or spare parts, please contact your local REBEL dealer or customer service department. Contact information can typically be found on the product packaging or the official REBEL website.
