NUU GARDEN 43-Inch 50,000 BTU Propane Gas Fire Pit Table Instruction Manual

1. Important Safety Information

Please read and understand all safety warnings and instructions before assembling, operating, or servicing this fire pit table. Failure to follow these instructions could result in property damage, bodily injury, or death.

• Outdoor Use Only: This fire pit table is designed for outdoor use only. Do not use indoors or in an enclosed area.
• Ventilation: Ensure adequate ventilation around the fire pit table. Do not obstruct airflow.
• Clearance: Maintain a minimum clearance of 36 inches (91 cm) from the top and sides to combustible materials.
• Children and Pets: Keep children and pets away from the fire pit table at all times. Never leave the fire pit table unattended when in use.
• Fuel: Use only liquid propane (LP) gas. Do not use any other fuel.
• Propane Tank: Use a standard 20 lb propane tank (not included). Ensure the tank is securely placed and connected.
• Leak Test: Perform a leak test on all gas connections before initial use and after any tank change.
• Hot Surfaces: The fire pit table surfaces become hot during operation. Avoid direct contact.
• Emergency: In case of a gas leak or fire, immediately turn off the gas supply at the tank and evacuate the area.

2. Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, do not attempt to assemble the product.

• Fire Pit Table Base (PE Rattan Weaved Steel Frame)
• Aluminum Tabletop
• Stainless Steel Burner Assembly (50,000 BTU)
• Metal Protective Lid
• Glass Beads
• Water-Proof Oxford Cover
• Hardware Pack (bolts, screws, AAA battery for igniter)
• Instruction Manual

Image: Components included with the NUU GARDEN Fire Pit Table, showing the table, lid, glass beads, and cover.

3. Setup and Assembly

Assembly typically requires two people due to the weight and size of components. Follow the numbered instructions provided in the included manual for detailed steps.

1. Unpack Components: Carefully remove all parts from the packaging. Place them on a soft, clean surface to prevent scratches.
2. Assemble Base: Attach the side panels to the main frame using the provided hardware. Ensure all connections are secure.
3. Install Propane Tank: Open the access door on the side of the fire pit table. Place a standard 20 lb propane tank (not included) onto the tank support. Connect the gas hose from the burner assembly to the propane tank. Tighten securely by hand.
4. Place Burner Assembly: Carefully lower the stainless steel burner assembly into the designated opening in the tabletop.
5. Add Glass Beads: Distribute the provided glass beads evenly over the burner area. Ensure the igniter and burner holes are not completely covered.
6. Install Igniter Battery: Locate the battery compartment for the electronic igniter. Insert one AAA battery (included) with the correct polarity.

Image: Overview of fire pit table dimensions, included cover, and the required 20 lb propane cylinder.

Image: Detailed view of how to install the propane tank within the fire pit's internal compartment.

4. Operating Instructions

Follow these steps to safely ignite and operate your fire pit table.

1. Open Gas Supply: Slowly turn the valve on the propane tank counter-clockwise to open the gas supply.
2. Ignite: Locate the control panel on the side of the fire pit table. Push and hold the igniter button while simultaneously turning the control knob to the 'ON' position. Continue holding the igniter button for 5-10 seconds until the flame is established.
3. Adjust Flame: Once ignited, release the igniter button. Use the control knob to adjust the flame height to your desired level (Low to Max).
4. To Turn Off: Turn the control knob to the 'OFF' position. Then, turn the valve on the propane tank clockwise to completely shut off the gas supply.

Image: Visual guide on how to use the safe ignition device and adjust the flame.

5. Maintenance

Proper maintenance ensures the longevity and safe operation of your fire pit table.

• Cleaning: Allow the fire pit table to cool completely before cleaning. Wipe surfaces with a soft, damp cloth. Do not use abrasive cleaners.
• Cover Usage: Use the provided water-proof Oxford cover when the fire pit table is not in use to protect it from weather elements.
• Glass Beads: Periodically inspect the glass beads for debris. Clean as needed.
• Burner Inspection: Regularly check the burner and gas connections for any signs of damage or blockage.

Image: The PVC-coated Oxford cover provides protection against wind, rain, and snow.

6. Troubleshooting

If you encounter issues, refer to this section before contacting customer support.

• No Ignition:
  • Check if the propane tank valve is fully open.
  • Ensure the igniter battery is correctly installed and not depleted.
  • Verify gas connections are secure and there are no leaks.
• Low Flame:
  • Check propane tank level; it may be low.
  • Ensure the control knob is set to a higher flame position.
  • Inspect burner holes for any blockages.
• Flame Goes Out:
  • Ensure the propane tank is not empty.
  • Check for strong winds that might be extinguishing the flame (consider a wind guard if not already present).

7. Specifications

8. Warranty and Support

For warranty information or customer support, please refer to the contact details provided in your product packaging or visit the NUU GARDEN official website. Keep your purchase receipt for warranty claims.