Introduction
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your Mintu Drain Pump Motor. This replacement part is specifically designed for various Kenmore washing machine models. Please read this manual thoroughly before attempting any installation or repair to ensure safe and correct usage and to prevent damage to your appliance.
Important Safety Information
- Disconnect Power: Always disconnect the washing machine from its electrical power source before attempting any installation, maintenance, or repair. Failure to do so can result in electric shock or serious injury.
- Professional Installation Recommended: If you are not experienced with appliance repair, it is recommended to seek assistance from a qualified technician.
- Wear Protective Gear: Wear appropriate personal protective equipment, such as gloves and safety glasses, during installation to protect against potential hazards.
- Water Drainage: Ensure all water is completely drained from the washing machine tub and hoses before removing the old pump to prevent spills and potential electrical hazards.
- Check Connections: After installation, verify all electrical and hose connections are secure and free from leaks before restoring power and water supply.
Compatible Kenmore Washing Machine Models
This Mintu Drain Pump Motor is compatible with a wide range of Kenmore washing machine models. Please verify your washing machine's model number against the list below to ensure compatibility. If your specific model number is not listed, please consult your appliance's original service manual or contact a service professional for verification.
Partial List of Compatible Models:
- 796.41072311
- 796.41073310
- 796.41073311
- 796.41162411
- 796.41172210
- 796.41172211
- 796.41172212
- 796.41182310
- 796.41182311
- 796.41262610
- 796.40021.900
- 796.40272.800
- 796.40272.900
- 796.40311.900
- 796.40318.900
- 796.40441.900
- 796.40448.900
- 796.40512.900
- 796.40518.900
- 796.41002610
- 796.41002612
- 796.41003610
- 796.41003611
- 796.41022.900
- 796.41028.900
- 796.41029.900
- 796.41262611
- 796.41272210
- 796.41272211
- 796.41282310
- 796.41282311
- 796.41283310
- 796.41283311
- 796.41302610
- 796.41303610
- 796.41372210
- 796.41372211
- 796.41379210
- 796.41382410
- 796.41382411
- 796.41383410
- 796.41383411
- 796.41392510
- 796.41392511
- 796.41393510
- 796.41393511
- 796.41393610
- 796.41472210
- 796.41473210
- 796.41482410
- 796.41482411
- 796.41483410
- 796.41483411
- 796.41532.110
- 796.41532210
- 796.41538.110
- 796.41542.110
- 796.41542210
- 796.41548.110
- 796.41548210
- 796.41549.110
- 796.41549210
- 796.41582412
- 796.41583410
- 796.41583411
- 796.41682610
- 796.41683610
- 796.41722.010
- 796.417220x11x280
Product Overview
The Mintu Drain Pump Motor is a critical component in your washing machine, responsible for expelling water from the tub during the drain and spin cycles. This replacement unit is designed to meet or exceed the specifications of the original part, ensuring efficient and reliable operation.
Image 1: Front view of the Mintu Drain Pump Motor, showing the impeller housing and the white impeller blades. This component is essential for moving water out of the washing machine tub.
Image 2: Side view of the Mintu Drain Pump Motor, highlighting the motor housing and the electrical connector terminals. Proper connection to the washing machine's wiring harness is crucial for its function.
Installation Instructions
Follow these steps carefully to replace your washing machine's drain pump motor. Refer to your washing machine's specific service manual for detailed panel removal and component location instructions, as these can vary by model.
- Prepare the Appliance: Ensure the washing machine is completely disconnected from its electrical power supply and water supply. Move the machine to an area with adequate space for safe access to its internal components.
- Drain Residual Water: If the machine contains water, manually drain it using the drain hose or by accessing the pump filter, if applicable. Place towels or a shallow pan to catch any remaining water.
- Access the Drain Pump: Depending on your washing machine model, you may need to remove the front panel, rear panel, or tilt the machine back to access the drain pump. Consult your washing machine's service manual for precise instructions.
- Disconnect Hoses: Carefully disconnect the inlet and outlet hoses from the old drain pump. Be prepared for residual water. Note their positions for correct reattachment.
- Disconnect Electrical Connections: Unplug the electrical connector(s) from the old drain pump motor. Taking a photo of the wiring configuration before disconnecting can be helpful for reassembly.
- Remove Old Pump: Unmount the old drain pump from its housing or brackets. This may involve unscrewing fasteners or releasing clips.
- Install New Pump: Position the new Mintu Drain Pump Motor in the same location as the old one. Secure it with the appropriate fasteners or clips, ensuring it is firmly seated.
- Reconnect Electrical Connections: Attach the electrical connector(s) to the new pump motor, ensuring a secure and tight fit.
- Reconnect Hoses: Reattach the inlet and outlet hoses to the new pump, securing them with clamps if present. Verify there are no kinks or loose connections that could cause leaks.
- Reassemble Appliance: Reattach any panels or covers that were removed during the process.
- Test Operation: Reconnect the washing machine to the water supply and power. Run a short drain or rinse cycle to check for proper operation and leaks. Monitor the area around the pump for any signs of water leakage during the cycle.
Operating Principles
The drain pump motor operates automatically as an integral part of your washing machine's cycle. Once correctly installed, it requires no manual intervention for its primary function. During the drain cycle, the washing machine's control board sends an electrical signal to the drain pump motor, activating it to expel water from the wash tub through the drain hose. The pump continues to operate during the spin cycle to remove any remaining water as the tub spins at high speed.
Normal Operation Indicators:
- A consistent humming sound during the drain cycle, followed by the audible flow of water being expelled.
- The washing machine successfully drains water and completes its cycles without displaying error codes related to draining issues.
Maintenance
The Mintu Drain Pump Motor is designed for durability and generally requires minimal maintenance. However, regular checks of your washing machine's drain system can help prevent issues and prolong the life of the pump.
- Check for Obstructions: Periodically check the washing machine's drain filter (if accessible) for lint, coins, or small objects that could obstruct the pump's impeller. Clear any blockages found promptly.
- Inspect Hoses: Occasionally inspect the drain hoses for kinks, cracks, or blockages. Ensure they are properly secured and free-flowing.
- Listen for Unusual Noises: Pay attention to any unusual grinding, rattling, or excessively loud humming noises during the drain cycle, which could indicate an issue with the pump or an obstruction.
Troubleshooting
If your washing machine is experiencing draining issues after installing the new pump, consider the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Washing machine does not drain water. | 1. Drain hose kinked or blocked. 2. Drain filter clogged. 3. Electrical connection to pump loose. 4. Washing machine control board issue. | 1. Straighten drain hose; clear any blockages. 2. Clean the drain filter. 3. Disconnect power, then check and secure electrical connections to the pump. 4. Consult a qualified technician for control board diagnosis. |
| Pump is noisy during operation. | 1. Object caught in impeller. 2. Loose mounting of the pump. 3. Pump motor failing (less likely with a new pump). | 1. Disconnect power, access pump, and carefully remove any foreign objects. 2. Ensure the pump is securely mounted to its housing or brackets. 3. If noise persists and the pump is new, verify correct installation or contact the supplier. |
| Water leaks from pump area. | 1. Hoses not properly secured. 2. Damaged hose or seal. 3. Incorrect pump installation. | 1. Disconnect power, then check and tighten hose clamps. 2. Inspect hoses and seals for damage; replace if necessary. 3. Review installation steps to ensure all connections are correct and tight. |
If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.
Specifications
| Feature | Detail |
|---|---|
| Brand | Mintu |
| Product Type | Drain Pump Motor |
| Material | Stainless Steel (internal components), Plastic (housing) |
| Color | Black |
| Power Source | AC/DC (compatible with washing machine's power supply) |
| Compatibility | Kenmore Washing Machines (various models, see compatibility section) |
| UPC | 824252608483 |
Warranty Information
Specific warranty details for this Mintu product may vary depending on the retailer and region. Please refer to the product packaging or the seller's product listing for the most accurate and up-to-date warranty information. It is advisable to retain your proof of purchase for any potential warranty claims.
Customer Support
For technical assistance, troubleshooting beyond the scope of this manual, or inquiries regarding warranty, please contact the seller or manufacturer directly through the platform where the product was purchased. When contacting support, please provide your product model number and purchase date for faster and more efficient service.