Introduction
Thank you for choosing the DieseRC RF 433MHz Wireless Light Switch System. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your 1-Gang wireless switch and receiver. This system offers a convenient, no-wiring solution for controlling lighting and other electrical appliances.
Safety Information
- Always disconnect power at the circuit breaker before installing or servicing any electrical components.
- Installation should be performed by a qualified electrician or in accordance with local electrical codes.
- Do not exceed the maximum load rating of 10A for the receiver.
- Ensure all wire connections are secure to prevent electrical hazards.
- Keep the device away from water and extreme temperatures.
Package Contents
- 1 x DieseRC 1-Gang Wireless Switch (Transmitter)
- 1 x DieseRC RF 433MHz Receiver
- Mounting Screws
- Double-sided Adhesive Tape
- 1 x 12V 27A Battery (pre-installed in switch)
Setup and Installation
1. Receiver Installation
The mini-sized receiver (47x42x23mm) is designed to be installed between the power supply and the appliance. It can be easily concealed within most electrical boxes or junction boxes. Ensure power is disconnected before wiring.
- Connect the Live (L) wire from your power source to the 'Input L' terminal on the receiver.
- Connect the Neutral (N) wire from your power source to the 'Input N' terminal on the receiver.
- Connect the Live (L) wire of your appliance (e.g., light) to the 'Output L' terminal on the receiver.
- Connect the Neutral (N) wire of your appliance to the 'Output N' terminal on the receiver.
2. Wireless Switch Installation
The wireless switch requires no wiring and can be placed or mounted anywhere. It can be fixed using the provided double-sided adhesive tape or screws.
- Adhesive Mounting: Clean the desired surface thoroughly. Apply the double-sided tape to the back of the switch and firmly press it onto the surface.
- Screw Mounting: Use the provided screws to secure the switch to a wall or other suitable surface.
3. Pairing (Learning) the Switch and Receiver
To establish communication between the wireless switch and the receiver, follow these pairing steps:
- Ensure the receiver is powered on.
- Press the learning button on the receiver twice. Wait for 3 seconds. The indicator light on the receiver will blink.
- Press one button on the wireless switch. Wait for 3 seconds. The indicator light on the receiver will stop blinking, indicating successful pairing.
Operating Instructions
Basic Operation
Once paired, simply press the button on the wireless switch to toggle the connected appliance (e.g., light) ON or OFF. The switch provides a tactile click and a subtle LED indicator upon activation.
Multi-Control Scenarios
The DieseRC system supports flexible control configurations:
- Multiple Switches Control One Lamp: You can pair up to 10 wireless switches with a single receiver, allowing control from various locations (e.g., a 3-way switch setup).
- One Switch Controls Multiple Lamps: A single wireless switch can be paired with multiple receivers, enabling simultaneous control of several lights or appliances.
Signal Range
The RF 433MHz signal can transmit through walls, floors, doors, and panels. In open areas, the control range can extend up to 50 meters. For stronger signal reception, the receiver's antenna can be carefully extended.
Maintenance
Battery Replacement (Wireless Switch)
The wireless switch is powered by a 12V 27A battery, which typically lasts about 5 years. To replace the battery:
- Carefully open the switch casing.
- Remove the old 12V 27A battery.
- Insert a new 12V 27A battery, ensuring correct polarity.
- Close the switch casing securely.
Cleaning
Wipe the switch and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the devices in water.
Troubleshooting
Signal Issues
- If the signal reception is weak, try extending the antenna on the receiver.
- Ensure the switch battery is not depleted.
- Verify that the switch and receiver are within the effective operating range.
Clearing Paired Devices (Reset)
To clear all paired wireless switches from a receiver:
- Ensure the receiver is powered on.
- Press the learning button on the receiver 8 times. Wait for 3 seconds. The indicator light will blink rapidly and then turn off, indicating that all paired devices have been cleared.
Specifications
| Feature | Specification |
|---|---|
| Brand | DieseRC |
| Model Number | 750828381477 |
| Product Dimensions (Switch) | 8.8 x 8.8 x 2.3 cm |
| Product Weight (Switch) | 60 grams |
| Receiver Dimensions | 4.7 x 4.2 x 2.3 cm |
| Operating Voltage (Receiver) | AC 85V ~ 250V |
| Current Rating (Receiver) | 10 A |
| RF Frequency | 433 MHz |
| Learning Code | EV1527 |
| Switch Battery | 1 x 12V 27A (included) |
| Switch Lifespan | Over 500,000 clicks |
| Receiver Relay Lifespan | Over 400,000 uses |
| Material | Plastic |
| Switch Type | Push Button |
| Terminal Type | Screw |
| Country of Origin | China |
Warranty Information
DieseRC products are manufactured to high-quality standards. For specific warranty details, please refer to the product packaging or contact DieseRC customer support. Generally, products are covered against defects in materials and workmanship under normal use.
Customer Support
If you encounter any issues or have questions regarding your DieseRC Wireless Light Switch System, please contact our customer support team. Refer to the product packaging or the retailer's website for contact information.
