Einhell Power X-Change 18V Cordless Paint Sprayer User Manual

Introduction

The Einhell TC-SY 18/60 Li-Solo cordless paint spray system is designed for efficient and precise application of paints, glazes, detergents, impregnating agents, and oils. This handheld system is ideal for small to medium-sized work surfaces, offering cordless freedom and ease of use. As a member of the Power X-Change family, it operates with any 18V Power X-Change battery (battery and charger sold separately).

Safety Information

Always prioritize safety when operating power tools. Read and understand all safety warnings and instructions provided in the product packaging and this manual before use. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.

• Wear appropriate personal protective equipment (PPE) including eye protection, respiratory protection (mask), and gloves.
• Ensure the work area is well-ventilated.
• Keep children and bystanders away while operating the sprayer.
• Do not spray flammable liquids near open flames or ignition sources.
• Always disconnect the battery before cleaning, adjusting, or performing maintenance.
• Refer to the product packaging for specific safety warnings and precautions related to the materials being sprayed.

Product Overview

Familiarize yourself with the components of your Einhell paint sprayer.

Figure 1: Einhell TC-SY 18/60 Li-Solo Cordless Paint Sprayer and included accessories.

Included Components:

• Cordless paint spray system (spray gun body)
• Spray gun attachment with 800 ml container
• Cleaning brush
• Tool for changing plastic needles
• Cleaning needle with plastic protective tube
• 2.0 mm nozzle
• 2.5 mm nozzle
• 100 ml container for viscosity testing
• Lid for 800 ml paint container

Figure 2: Detailed view of the cleaning brush, cleaning needle, two nozzles, viscosity measuring cup, and container lid.

Setup

1. Battery Installation

The TC-SY 18/60 Li-Solo is part of the Einhell Power X-Change family and requires an 18V Power X-Change battery and charger, which are not included with this sprayer and must be purchased separately.

Figure 3: Important note: Battery and charger are sold separately.

1. Ensure the sprayer is switched off.
2. Insert a charged 18V Power X-Change battery into the battery slot on the handle until it clicks into place.
3. To remove, press the release button on the battery and slide it out.

2. Assembling the Spray Gun

Figure 4: Exploded view illustrating the assembly of the spray gun head and container.

1. Attach the spray gun attachment (with the 800 ml container) to the main spray gun body. Ensure it is securely fastened.
2. Select the appropriate nozzle (2.0 mm or 2.5 mm) based on the viscosity of your material. The 2.5 mm nozzle is generally for thicker materials, and 2.0 mm for thinner.
3. Insert the chosen nozzle into the spray head and secure it with the nozzle cap.

3. Preparing Paint/Material and Viscosity Test

Before filling the container, it is crucial to test the viscosity of your paint or material to ensure optimal spraying performance.

Figure 5: The sprayer is suitable for various materials including lacquers and glazes.

1. Stir the paint/material thoroughly.
2. Fill the supplied 100 ml viscosity measuring cup with the material.
3. Measure the time it takes for the material to completely flow out of the cup. Refer to the paint manufacturer's recommendations for ideal viscosity. If the material is too thick, dilute it according to the manufacturer's instructions (e.g., with water for water-based paints, or appropriate thinner for oil-based paints).
4. Once the correct viscosity is achieved, fill the 800 ml paint container with the prepared material. Do not overfill.
5. Securely attach the container to the spray gun.

Operating Instructions

1. Spraying Technique

Figure 6: Proper technique for spraying, maintaining a consistent distance and motion.

• Hold the spray gun at a consistent distance (typically 15-30 cm or 6-12 inches) from the surface.
• Move the sprayer in smooth, even strokes, overlapping each pass slightly to ensure uniform coverage.
• Avoid tilting the sprayer excessively, as this can affect paint flow.
• Always start spraying off the workpiece and end off the workpiece to prevent uneven application.

2. Adjusting Spray Pattern

The adjustable air cap allows you to select vertical, horizontal, or round spray jets to suit your application needs.

Figure 7: Adjust the air cap to switch between horizontal, vertical, and round spray patterns.

• Horizontal Jet: For vertical surfaces, rotate the air cap to align the two horizontal prongs.
• Vertical Jet: For horizontal surfaces, rotate the air cap to align the two vertical prongs.
• Round Jet: For small areas or corners, rotate the air cap to align the single central prong.

3. Paint Flow Regulation

The paint quantity regulation knob allows for ideal adaptation of the paint application rate, up to 650 ml per minute.

Figure 8: The paint flow regulation knob allows precise control over material output.

• Turn the regulation knob to increase or decrease the amount of paint sprayed.
• Test the flow on a scrap piece of material before applying to your main project.

Maintenance and Cleaning

Proper cleaning after each use is essential to maintain the performance and longevity of your paint sprayer.

1. Empty Container: After spraying, empty any remaining material from the 800 ml container back into its original can or a suitable disposal container.
2. Initial Rinse: Fill the container with an appropriate cleaning solution (water for water-based paints, mineral spirits/thinner for oil-based paints). Spray the cleaning solution through the gun until it runs clear. Do this in a well-ventilated area or outdoors.
3. Disassemble: Disconnect the battery. Remove the spray gun attachment and disassemble the nozzle, air cap, and any other removable parts that came into contact with paint.
4. Thorough Cleaning: Use the supplied cleaning brush and cleaning needle to thoroughly clean all paint-bearing elements, including the nozzle, air cap, fluid tip, and the inside of the container. Pay special attention to small orifices to prevent clogging.
5. Rinse and Dry: Rinse all cleaned parts with clean water (if applicable to the cleaning solution used) and allow them to dry completely before reassembly.
6. Storage: Store the cleaned and reassembled sprayer in a dry, safe place, away from extreme temperatures and out of reach of children. The housing includes a suspension device for space-saving storage.

Troubleshooting

Refer to the table below for common issues and their solutions.

Specifications

Warranty and Support

Warranty Information

Einhell products are manufactured with quality and durability in mind. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Einhell website. Keep your proof of purchase for any warranty claims.

Customer Support

Should you encounter any issues or have questions regarding the operation, maintenance, or troubleshooting of your Einhell TC-SY 18/60 Li-Solo paint sprayer that are not covered in this manual, please contact Einhell customer support. Contact details can typically be found on the product packaging or the official Einhell website.