1. Product Overview
The SnapPower MotionLight is an innovative LED night light designed to integrate seamlessly with your existing duplex electrical outlets. It replaces the standard outlet cover plate, providing a motion-activated light source without occupying the outlet receptacles. This product features an automatic on/off sensor, adjustable brightness, and variable light duration settings, enhancing safety and convenience in various areas of your home.
Image 1.1: SnapPower MotionLight integrated into a duplex outlet, providing downward illumination.
The MotionLight is designed for simple installation, requiring no wires or batteries, and draws power directly from the outlet's side screw terminals. Its energy-efficient LEDs offer a long lifespan, providing dependable lighting with minimal maintenance.
2. Setup and Installation
Before beginning installation, ensure you have a standard duplex outlet with exposed side screw terminals. This product is not compatible with all outlet types.
- Step 1: Power Off
Locate the circuit breaker controlling the outlet where you intend to install the MotionLight. Turn off the power to this outlet. Verify the power is off using a voltage tester before proceeding. - Step 2: Remove Existing Cover Plate
Carefully unscrew and remove the existing cover plate from the duplex outlet. - Step 3: Inspect Outlet Box
Examine the area around the outlet's side screw terminals. Ensure these areas are clear of any obstructions or excess wiring that might prevent the MotionLight's prongs from making proper contact. The prongs must slide cleanly into the electrical box to connect with the outlet's terminals. - Step 4: Install MotionLight
Align the SnapPower MotionLight over the duplex outlet. Gently push the MotionLight into place, ensuring the two power prongs on the back of the plate slide into contact with the outlet's side screw terminals. Secure the MotionLight to the outlet box using the provided screw. Do not overtighten. - Step 5: Restore Power and Test
Return to your circuit breaker and restore power to the outlet. Darken the room to test the motion detection and light function.
Image 2.1: Rear view of the MotionLight, illustrating the power prongs for connection.
3. Operating Instructions
The SnapPower MotionLight features two small, three-position switches located on the side of the unit, allowing for customization of brightness and light duration.
3.1. Brightness Control
The switch on the left side controls the light output level:
- Bottom Position: Light Off
- Middle Position: Dim Light Output
- Top Position: Maximum Light Output (Bright)
3.2. Light Duration Control
The switch on the right side controls how long the light remains on after motion is detected:
- Bottom Position: 3 Minutes
- Middle Position: 1 Minute
- Top Position: 15 Seconds
3.3. Motion and Light Sensor
The MotionLight is equipped with an integrated motion sensor and a light sensor. The light will only activate when motion is detected in low ambient light conditions. This ensures the light does not turn on unnecessarily during daylight hours, conserving energy.
Image 3.1: MotionLights providing subtle illumination in a hallway.
Image 3.2: MotionLight providing ambient light in a bathroom setting.
4. Maintenance
The SnapPower MotionLight requires minimal maintenance. The LED lights are designed for a long lifespan (25+ years) and do not require replacement.
- Cleaning: To clean the surface of the MotionLight, gently wipe with a soft, dry cloth. Avoid using abrasive cleaners or excessive moisture, as this may damage the unit.
- Inspection: Periodically check the unit for any signs of damage or loose connections. If any issues are observed, turn off power at the circuit breaker and inspect the installation.
5. Troubleshooting
- Light Does Not Turn On:
- Ensure the circuit breaker for the outlet is on.
- Verify the brightness switch on the left side is not in the 'Off' (bottom) position.
- Check ambient light conditions. The light sensor prevents activation in bright environments. Test in a darkened room.
- Confirm the MotionLight's power prongs are making proper contact with the outlet's side screw terminals. Turn off power, remove the unit, and re-install carefully.
- Motion Sensor Not Detecting Movement:
- Ensure there are no obstructions directly in front of the motion sensor.
- The motion sensor has a specific detection range and angle. Movement directly in front of the unit is most reliably detected. Consider the placement relative to typical pathways.
- Unit Does Not Fit Outlet:
- The SnapPower MotionLight for Duplex Outlets is designed for standard duplex outlets with exposed side screw terminals. It is not compatible with all outlet types (e.g., some older outlets or those with recessed terminals).
- Ensure you have the correct SnapPower product for your specific outlet type (Duplex, Decor, or GFCI).
6. Specifications
| Feature | Detail |
|---|---|
| Brand | SnapPower |
| Model Number | 850033353181 |
| ASIN | B098SHLNNJ |
| Item Weight | 1.02 Pounds |
| Color | Ivory |
| Material | Plastic (duplex) |
| Light Fixture Form | Wall |
| Room Type | Bathroom, Bedroom, Hallway, Kitchen |
| Power Source | Outlet (no batteries required) |
| Light Type | LED |
| LED Lifespan | 25+ years |
7. Warranty Information
Specific warranty details for the SnapPower MotionLight are not provided in the available product information. For warranty inquiries, please refer to the official SnapPower website or contact their customer support directly.
8. Support
For further assistance, technical support, or additional product information, please visit the official SnapPower website. Contact details for customer service are typically available on the manufacturer's website.
