1. Product Overview
The SnapPower SwitchLight is a double-gang light switch wall plate with integrated LED night lights. It is designed to provide subtle illumination in dark areas, featuring an auto on/off sensor and adjustable brightness settings (bright, dim, off). This product eliminates the need for additional night lights or wiring, offering a clean and convenient lighting solution.
Image 1: SnapPower SwitchLight Double-Gang Toggle Wall Plate with the integrated LED night light illuminated, casting a soft glow downwards.
2. Safety Information
- WARNING: Always turn off power at the circuit breaker before installing or servicing the SwitchLight. Failure to do so may result in serious injury or death.
- Ensure the existing light switch is compatible with a double-gang toggle style wall plate.
- Do not install in wet or damp locations.
- This product is for indoor use only.
3. Installation Guide
Installation of the SnapPower SwitchLight is designed to be simple and requires no wiring. Follow these steps:
- Turn Off Power: Locate your circuit breaker panel and turn off the power to the light switch you intend to replace. Verify the power is off by attempting to operate the light switch.
- Remove Existing Wall Plate: Carefully unscrew and remove your current double-gang toggle light switch wall plate.
- Prepare SwitchLight: The SwitchLight features patented power prongs on the back that make contact with the screws on your existing light switch. Ensure these prongs are aligned with the screw terminals of your light switch.
- Install SwitchLight: Place the SnapPower SwitchLight over your existing light switch, aligning the openings with the toggle switches and the screw holes. Gently press the plate firmly against the wall to ensure the power prongs make secure contact with the side screws of the light switch.
- Secure Wall Plate: Use the provided screws to fasten the SwitchLight to the wall. Do not overtighten.
- Restore Power: Return to your circuit breaker panel and turn the power back on.
- Test: The night light should illuminate automatically in a dark environment.
Image 2: The reverse side of the SnapPower SwitchLight, displaying the green power prongs designed to connect directly to the light switch terminals for power.
4. Operating Instructions
The SnapPower SwitchLight features an integrated light sensor and a brightness adjustment switch.
- Automatic On/Off: The built-in light sensor detects ambient light levels. The LED night light will automatically turn on when the room is dark and turn off when sufficient light is present.
- Brightness Adjustment: On the bottom left corner of the wall plate, there is a small switch to adjust the brightness of the LED night light.
- Slide the switch to the left for a dim light setting.
- Slide the switch to the right for a bright light setting.
- Slide the switch to the center to turn the night light off completely.
Image 3: The SwitchLight installed in a bathroom, casting a soft, warm glow onto the counter and floor, enhancing visibility in low light conditions.
Image 4: Multiple SwitchLights installed in a kitchen, providing subtle under-cabinet lighting that illuminates the countertop and backsplash.
5. Maintenance
- Cleaning: To clean the SwitchLight, gently wipe it with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- LED Lifespan: The integrated LED lights are designed for a long lifespan, typically exceeding 25 years under normal use, eliminating the need for bulb replacement.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Night light does not turn on. | 1. Power is off at the circuit breaker. 2. Light sensor detects too much ambient light. 3. Brightness switch is set to 'Off'. 4. Poor contact with switch terminals. | 1. Check and restore power at the circuit breaker. 2. Test in a darker environment. 3. Adjust the brightness switch to 'Dim' or 'Bright'. 4. Ensure the wall plate is pressed firmly against the wall and screws are tightened to ensure proper contact with the switch terminals. |
| Night light flickers. | 1. Incompatible light bulb in the controlled fixture. 2. Loose connection at the switch terminals. | 1. Some LED bulbs may cause flickering. Try replacing the bulb in the controlled fixture with a different type or brand. 2. Turn off power at the breaker, remove the SwitchLight, and ensure the existing light switch's terminal screws are tightened. Reinstall the SwitchLight. |
| Wall plate does not sit flush. | Obstruction or uneven wall surface. | Ensure there are no wires or other obstructions behind the wall plate. Check for unevenness in the wall surface. |
7. Specifications
- Model: 851322008768
- Brand: SnapPower
- Material: Plastic
- Color: Ivory
- Configuration: Double-Gang
- Switch Type Compatibility: Toggle
- Installation Type: Screw-In (Snap-on power connection)
- Light Source: Built-in LED
- Features: Auto On/Off Sensor, Bright/Dim/Off Options
- Item Weight: 1.02 pounds
Image 5: An illustration showing the difference between Toggle and Rocker style light switches, indicating the compatibility of SwitchLight with various switch types.
8. Warranty and Support
For warranty information and customer support, please refer to the official SnapPower website or contact their customer service directly. Keep your purchase receipt for warranty claims.
SnapPower Official Website: www.snappower.com