Sealey LED220UV Rechargeable Aluminium Pocket Light with UV

1. Introduction

This instruction manual provides essential information for the safe and effective operation, maintenance, and care of your Sealey LED220UV Rechargeable Aluminium Pocket Light with UV. Please read this manual thoroughly before first use and retain it for future reference.

2. Product Features

• Powerful 3W COB (Chip-on-Board) LED for broad illumination.
• 1 x SMD (Surface-Mounted Device) LED for focused beam.
• 2 x UV SMD LEDs (390-400nm) for detection purposes.
• Integrated USB rechargeable Lithium-ion battery (3.7V 2200mAh).
• Charging indicator light (green/red).
• Durable aluminium construction with an anodized finish and rubber coating for enhanced grip.
• Strong magnetic pocket/belt clip for hands-free attachment.
• Additional strong magnet in the base for versatile positioning.
• Lumen Output: 220lm.
• Charging Time: Approximately 3 hours.

Image 2.1: Front view of the Sealey LED220UV pocket light, showcasing the COB LED and the SMD LEDs.

3. Package Contents

Please check the contents of your package. If any items are missing or damaged, contact your supplier immediately.

• Sealey LED220UV Rechargeable Aluminium Pocket Light with UV
• USB Charging Cable (typically included, though not explicitly listed as a separate component)

4. Safety Instructions

WARNING: Always observe basic safety precautions when using electrical products to reduce the risk of fire, electric shock, and personal injury.

• General Safety: Keep the light away from water, moisture, and extreme temperatures. Do not attempt to open or modify the device.
• Battery Safety: The device contains a Lithium-ion battery. Do not expose to fire or high temperatures. Do not puncture or disassemble the battery. Dispose of batteries responsibly according to local regulations.
• UV Light Safety: Avoid direct exposure of UV light to eyes and skin. UV-A light can be harmful with prolonged exposure. Use appropriate eye protection if working with UV light for extended periods.
• Children: Keep out of reach of children. This is not a toy.
• Charging: Use only the provided or a certified USB charging cable. Do not charge unattended.

5. Setup

5.1 Initial Charging

1. Before first use, fully charge the pocket light.
2. Locate the USB charging port, typically covered by a rubber flap, on the side or top of the unit.
3. Connect the small end of the USB charging cable to the light's charging port.
4. Connect the larger end of the USB cable to a suitable USB power source (e.g., computer USB port, USB wall adapter, or power bank).
5. The charging indicator light will illuminate red during charging.
6. Once fully charged (approximately 3 hours), the indicator light will turn green. Disconnect the light from the power source.

Image 5.1: Angled top view of the Sealey LED220UV, illustrating the location of the power button and the USB input port for charging.

6. Operating Instructions

6.1 Power On/Off and Mode Selection

The Sealey LED220UV features a single power button, typically located near the top of the unit, to cycle through its various lighting modes.

1. First Press: Activates the 3W COB LED for wide-area illumination.
2. Second Press: Switches to the 1 SMD LED for a more focused beam.
3. Third Press: Activates the 2 UV SMD LEDs for ultraviolet light applications.
4. Fourth Press: Turns the light off.

To turn the light off from any mode, simply press the button until the light cycles through all modes and turns off, or hold the button down for a few seconds (if applicable, refer to specific product behavior).

6.2 Using the Magnets

The pocket light is equipped with two strong magnets for hands-free operation:

• Pocket/Belt Clip Magnet: Located on the integrated clip, allowing the light to be attached to metallic surfaces or clothing for directional lighting.
• Base Magnet: Situated at the bottom of the unit, providing a stable base for upright positioning on metallic surfaces.

Image 6.1: The Sealey LED220UV in use, demonstrating its UV light capability to detect a fluorescent leak in an automotive engine bay. The magnetic base or clip can be used for hands-free operation.

Image 6.2: Side view of the Sealey LED220UV, highlighting the integrated magnetic pocket/belt clip for convenient attachment.

7. Maintenance

7.1 Cleaning

To clean the light, wipe it with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or internal components. Ensure the charging port cover is securely closed before cleaning.

7.2 Storage

When not in use, store the light in a cool, dry place, away from direct sunlight and extreme temperatures. For prolonged storage, it is recommended to charge the battery every 3-6 months to maintain its health.

8. Troubleshooting

• Light does not turn on: Ensure the battery is charged. Connect to a USB power source and check the charging indicator.
• Light does not charge: Verify the USB cable is securely connected to both the light and the power source. Try a different USB cable or power source. Ensure the charging port is clean and free of debris.
• Reduced brightness or short battery life: The battery may be nearing the end of its lifespan, or it may not be fully charged. Ensure the light is charged for the full 3 hours.

If troubleshooting steps do not resolve the issue, contact Sealey customer support or your retailer for assistance.

9. Specifications

10. Warranty Information

This Sealey LED220UV pocket light is covered by a 1-Year Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized modification, or normal wear and tear.

For warranty claims or service, please retain your proof of purchase and contact your retailer or Sealey customer support.

Image 10.1: Official Sealey 1 Year Guarantee logo, indicating the product warranty period.

11. Disposal Information

Waste Electrical and Electronic Equipment (WEEE) Directive:

Do not dispose of this product with household waste. This product contains a rechargeable Lithium-ion battery and electronic components that must be recycled responsibly. Please take it to a designated collection point for the recycling of electrical and electronic equipment. Proper disposal helps prevent potential negative consequences for the environment and human health.

For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.