Waterdrop WD-TK-FS 2.25G Gravity-Fed Stainless Steel Water Filter System User Manual

1. Introduction

The Waterdrop WD-TK-FS Gravity-Fed Water Filter System is designed to provide clean, filtered water for various uses, both indoors and outdoors. This system utilizes advanced filtration technology to reduce common contaminants, improving water quality and taste. It features a robust 304 food-grade stainless steel construction and is certified to meet NSF/ANSI 372 standards.

2. Components Included

Please ensure all components are present before beginning assembly:

• Upper Chamber (1)
• Lower Chamber (1)
• Water Level Spigot (1)
• Carbon Filters (Black) (2)
• Fluoride Filters (White) (2)
• Stand (1)
• Lid Knob (1)
• Lid (1)
• Wrench (1)
• Priming Washer (1)

Image: All components of the Waterdrop Gravity-Fed Water Filter System.

3. Setup Instructions

3.1. Lid Knob Assembly

1. Insert the knob screw and washer through the lid.
2. Fasten it securely with the knob.

3.2. Spigot Assembly

1. Unscrew the hex nut from the spigot.
2. Insert the spigot through the hole on the side of the lower chamber.
3. Tighten it securely with the hex nut and ensure the spigot is in the upright position.

Image: Detailed view of the metallic water level spigot.

3.3. Filter Flushing (Priming)

Before first use, filters must be flushed to remove any loose carbon particles.

1. Screw down the wing nut on the filter base until the height of the priming washer can be attached.
2. Press the priming washer onto the spigot and align it with the cold water outlet of your faucet.
3. Turn on the cold water to flush the filter for 60 seconds. Repeat for all filters.

3.4. Filter Installation

1. Remove the wing nut and filter washer from the carbon filter's threaded rod.
2. Insert the carbon filter's threaded rod into the holes in the upper chamber, with the filter entering into the same chamber.
3. Gently thread the filter washer and wing nut onto the threaded rod just below the upper chamber. Tighten manually with your hand.
4. Repeat for all filters (2 carbon, 2 fluoride). The system has two installation holes for carbon filters and two for fluoride filters.

Image: Illustration of the 6-stage advanced filtration process.

3.5. Final Assembly

1. Place the upper chamber, with installed filters, carefully onto the lower chamber.
2. Place the lid on the upper chamber.
3. Position the assembled system on the provided stand.

4. Operating Instructions

4.1. Filling the System

Pour untreated water into the upper chamber. The water will gravity-feed through the filters into the lower chamber. The filtration process is efficient and does not require power.

4.2. Dispensing Water

Use the metallic water level spigot on the lower chamber to dispense filtered water. The spigot is designed for leak-proof performance and easy operation.

Image: Real-time water level monitoring feature on the spigot.

4.3. Initial Water Discard

For the first two full batches of filtered water, it is recommended to discard the water. This helps to ensure any residual manufacturing dust or loose carbon fines are flushed from the system, preparing it for optimal use.

5. Maintenance

5.1. Filter Lifespan & Replacement

• Carbon Filters (Black): Effectively filter up to 6,000 gallons of water.
• Fluoride Filters (White): Effectively filter up to 1,000 gallons of water.

Replace filters according to their recommended lifespan or if you notice a decrease in water flow or a change in water taste/odor. Replacement instructions are similar to initial installation.

5.2. Cleaning the System

The 304 food-grade stainless steel chambers are easy to clean. Periodically wipe down the exterior with a soft cloth. For interior cleaning, disassemble the system and wash the chambers with mild soap and water. Rinse thoroughly before reassembly.

6. Troubleshooting

• Slow Filtration: Ensure filters are properly primed and not clogged. If flow remains slow after cleaning, filters may need replacement.
• Leaks: Check all connections, especially the spigot and filter wing nuts, to ensure they are securely tightened. Ensure all washers and gaskets are correctly seated.
• Unusual Taste or Odor: Re-flush the filters. If the issue persists, filters may be exhausted and require replacement.
• Water Level Indicator Not Working: Check for any obstructions in the clear tube. Ensure the tube is securely attached and free from damage.

7. Specifications

Image: Product dimensions and compact design.

8. Warranty and Support

Waterdrop products are designed for durability and performance. For specific warranty details, product support, or to purchase replacement filters, please refer to the official Waterdrop website or contact their customer service directly. A customer review mentioned a replacement part was fully covered under warranty after 3 years of use, indicating good post-purchase support.

For further assistance, please visit the Waterdrop Store on Amazon.