LARSON Certified White Storm Door Piston Hold-Open Kit

Introduction

This manual provides instructions for the installation, operation, and maintenance of your LARSON Certified White Storm Door Piston Hold-Open Kit. This kit is designed to provide convenient hands-free access and secure closing for storm doors.

Key Features:

• Provides a hands-free hold-open function for convenience.
• Constructed with non-corrosive components, suitable for various environments, including coastal locations.
• Allows the storm door to open a full 90 degrees when installed correctly.
• Compatible with wood, metal, and vinyl storm doors.
• Features easy-to-use settings and adjustable closing speed for secure latching.

Product Overview

Package Contents:

Verify that all components are present before beginning installation.

• Storm Door Piston Hold-Open Closer
• Mounting Brackets
• Mounting Screws
• Installation Instructions (paper)

Image: Components of the LARSON Storm Door Piston Hold-Open Kit, showing the white piston, mounting hardware, and a small instruction sheet.

Image: The LARSON Storm Door Piston Hold-Open Kit in its assembled form, featuring the white piston and attached mounting bracket.

Image: A visual comparison showing both black and white versions of the LARSON storm door closers, highlighting the hold-open button feature.

Setup and Installation

This kit is designed for screw-in installation and can be used on wood, metal, or vinyl storm doors. Refer to the included paper instructions for detailed diagrams and specific measurements.

Tools Required (Not Included):

• Drill
• Screwdriver
• Measuring Tape
• Pencil

General Installation Steps:

1. Prepare the Door: Ensure the storm door is securely mounted and operates smoothly.
2. Position Brackets: Determine the optimal placement for the mounting brackets on both the door frame and the storm door itself. The closer should be positioned to allow the door to open a full 90 degrees. Mark screw locations with a pencil.
3. Drill Pilot Holes: Drill pilot holes at the marked locations. Use a drill bit appropriate for your door material (wood, metal, or vinyl) and screw size.
4. Attach Brackets: Securely fasten the mounting brackets using the provided screws.
5. Install Closer: Attach the piston closer to the installed brackets. Ensure the closer is oriented correctly according to the included instructions.
6. Test Operation: Slowly open and close the storm door to verify proper function.
7. Adjust Closing Speed: Refer to the "Operating Instructions" section to adjust the closing speed as needed.

Image: Packaging for the LARSON Storm Door Closer, showing product details and indicating that mounting hardware and instructions are included.

Operating Instructions

Using the Hold-Open Function:

The LARSON Storm Door Piston Hold-Open Kit allows you to keep your storm door open for hands-free access.

1. To Engage Hold-Open: Open the storm door to the desired position. Locate the hold-open button or lever on the closer piston. Press or tap this mechanism to engage the hold-open feature. The door should now remain open.
2. To Release Hold-Open: Gently push the door further open, then allow it to close. The hold-open mechanism should disengage, and the door will begin to close.

Adjusting Closing Speed:

The closing speed of your storm door can be adjusted to your preference for secure latching.

• Locate the adjustment screw on the end of the closer piston.
• Turn the screw clockwise to decrease the closing speed (slower).
• Turn the screw counter-clockwise to increase the closing speed (faster).
• Make small adjustments and test the door's closing action until the desired speed is achieved. Ensure the door latches securely without slamming.

Maintenance

Regular maintenance ensures optimal performance and extends the life of your storm door closer.

• Cleaning: Periodically wipe down the closer with a soft, damp cloth to remove dust and debris. Avoid abrasive cleaners.
• Lubrication: If the piston action feels stiff or noisy, apply a small amount of silicone-based lubricant to the moving parts and the piston rod. Do not use oil-based lubricants as they can attract dirt.
• Check Fasteners: Annually inspect all mounting screws and ensure they are tight. Re-tighten if necessary to prevent loosening over time.
• Inspect for Damage: Check the closer and brackets for any signs of wear, bending, or damage. Replace any damaged components immediately.

Troubleshooting Common Issues

If you encounter issues with your storm door closer, refer to the following common problems and solutions:

• Door does not close fully or latches improperly:
  • Check the closing speed adjustment screw. It may need to be adjusted to a faster setting.
  • Ensure all mounting screws are tight and the closer is securely attached.
  • Verify that there are no obstructions preventing the door from closing completely.
• Door slams shut:
  • Adjust the closing speed screw counter-clockwise to slow down the closing action.
• Hold-open function does not engage or release:
  • Ensure the door is opened far enough for the hold-open mechanism to engage.
  • Check for any debris or obstruction around the hold-open button/lever.
  • If the mechanism feels stiff, a light application of silicone lubricant may help.
  • If the hold-open function consistently fails, the internal mechanism may be worn or damaged, requiring replacement.
• Closer makes excessive noise:
  • Apply silicone lubricant to the piston rod and moving parts.
  • Check for loose mounting screws or misaligned brackets.

Technical Specifications

Warranty Information

This LARSON product is covered by a manufacturer's warranty. For specific details regarding warranty coverage, duration, and claims procedures, please refer to the warranty documentation included with your product packaging or visit the official Larson website. Keep your proof of purchase for warranty purposes.

Customer Support

If you require further assistance, have questions not covered in this manual, or need to report a defective product, please contact Larson customer support. Contact information can typically be found on the product packaging or on the official Larson Manufacturing website.

For more information, you may visit the Larson Store on Amazon.