Introduction
This manual provides detailed instructions for the proper setup, operation, and maintenance of your Waterdrop 200-Gallon Long-Life 10-Cup Water Filter Pitcher, Model WD-PT-61B. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.
The Waterdrop filter pitcher is designed to provide clean, fresh-tasting water by reducing chlorine, taste, odor, PFOA/PFOS, and other impurities. It is NSF 42 and 372 certified for material safety and contaminant reduction.
Product Overview
The Waterdrop water filter pitcher consists of several key components:
- Pitcher Body: The main container for filtered water.
- Filter Reservoir: Holds the unfiltered water and the filter cartridge.
- Lid: Features a dust-proof flip lid for easy refilling and a smart filter life indicator.
- Filter Cartridge: The core filtration component.
- Handle: Ergonomically designed for comfortable grip.
Figure 1: Waterdrop 10-Cup Water Filter Pitcher (Model WD-PT-61B) with its components.
Figure 2: Key design features including the top dust-proof flip lid and ergonomic handle.
Setup and Initial Use
- Wash Components: Hand wash the pitcher body, lid, and filter reservoir with a mild detergent. Rinse thoroughly with water. Do not use abrasive cleaners or place in a dishwasher.
- Prepare Filter Cartridge: Remove the filter cartridge from its packaging. Submerge the filter fully in cold tap water for 10 minutes to soak it. This removes air bubbles and activates the filter for optimal performance.
- Install Filter: Insert the prepared filter cartridge into the filter reservoir. Press firmly to ensure a tight seal. The O-ring on the filter cartridge prevents unfiltered water from bypassing the filter.
- Fill Pitcher: Place the lid on the pitcher. Fill the filter reservoir with cold tap water. The dust-proof flip lid allows for easy refilling directly from the tap.
- Discard Initial Water: Discard the first two pitchers of filtered water. This primes the filter and removes any loose carbon particles.
- Activate Filter Life Indicator: After installing a new filter, press and hold the smart life indicator button on the lid for 5 seconds until it flashes blue. This resets the filter life record.
Figure 3: Water filtering through the installed cartridge into the pitcher body.
Operating Instructions
Using your Waterdrop filter pitcher is straightforward:
- Fill: Open the dust-proof flip lid and fill the filter reservoir with cold tap water. The 360° all-direction water inlet allows for quick filling.
- Filter: Allow the water to pass through the filter cartridge into the main pitcher body. The fast flow rate of up to 0.5 gallons per minute (gpm) ensures quick filtration.
- Pour: Once filtered, pour the clean water from the pitcher. The specially designed handle provides a strong, comfortable grip.
Figure 4: Multi-stage filtration system for comprehensive water purification.
Figure 5: Smart filter life indicator for timely filter replacement.
Video 1: A detailed guide on how the smart life indicator works, including its different light signals for filter status.
Filter Replacement
The filter cartridge has a lifespan of up to 200 gallons or 3 months, whichever comes first. The smart life indicator will notify you when it's time for a replacement:
- Blue Light: Filter life is good (more than 10 days remaining).
- Flashing Red Light: Filter needs replacing soon (1-10 days remaining).
- Solid Red Light: Filter needs replacing now (0 days remaining).
To replace the filter:
- Remove the lid and the old filter cartridge from the reservoir.
- Prepare the new filter cartridge by submerging it in cold tap water for 10 minutes.
- Insert the new filter firmly into the reservoir until it is securely seated.
- Replace the lid.
- Press and hold the smart life indicator button for 5 seconds until it flashes blue to reset the filter life record.
- Discard the first two pitchers of filtered water from the new filter.
Figure 6: Waterdrop filter cartridge, designed for a 3-month lifespan.
Maintenance and Care
- Cleaning: Hand wash all non-filter components (pitcher body, lid, reservoir) with mild soap and water. Rinse thoroughly. Do not use abrasive cleaners or put them in the dishwasher.
- Filter Handling: Always handle the filter cartridge with clean hands.
- Storage: If storing the pitcher for an extended period, ensure all components are clean and dry. Store new, unused filters in a cool, dry place away from direct sunlight.
- Avoid Direct Sunlight: Do not place the water filter pitcher in direct sunlight, as this can affect water quality and pitcher longevity.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow flow rate or no water output. | Filter not properly primed or clogged. |
|
| Smart life indicator not working. | Batteries are out of power. | Contact customer service for assistance. If within warranty, a replacement may be provided. |
| Water taste is not improved. | Filter not properly installed or expired. |
|
Specifications
| Feature | Detail |
|---|---|
| Model Number | WD-PT-61B |
| Capacity | 10 Cups |
| Filter Lifespan | Up to 200 Gallons or 3 Months |
| Certifications | NSF 42 (Chlorine Reduction), NSF 372 (Lead-Free Materials) |
| Contaminant Reduction | PFOA/PFOS, Chlorine, Taste, Odor, Sand, Limescale, Large Particles, Calcium, Magnesium ion, other impurities. (Note: Does not lower TDS value.) |
| Flow Rate | Up to 0.5 Gallons Per Minute (gpm) |
| Product Dimensions | 10"L x 5.28"W x 10.04"H |
| Material | BPA Free, tough materials |
| UPC | 840814194508 |
Warranty and Support
Waterdrop products typically come with a warranty. For specific warranty details and to register your product, please refer to the official Waterdrop website or contact customer service.
If you encounter any issues or have questions not covered in this manual, please contact Waterdrop customer service:
- Email: service@waterdropfilter.com
- Website: www.waterdropfilter.com
Please have your model number (WD-PT-61B) and purchase information ready when contacting support.
