Craftmade ZA3604-SA Canon Outdoor Wall Sconce Instruction Manual

Introduction

Thank you for purchasing the Craftmade ZA3604-SA Canon Outdoor Wall Sconce. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.

Important Safety Information

• WARNING: To avoid electric shock, disconnect power at the circuit breaker or fuse box before installation or servicing.
• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Contact a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• This fixture is approved for WET locations. Ensure all connections are properly sealed to prevent water intrusion.
• Use only the specified bulb type and wattage. Exceeding the maximum wattage may cause overheating and damage to the fixture.
• Do not install any fixture assembly closer than 6 inches from any combustible material.
• Always handle glass components with care.

Package Contents

Carefully unpack your fixture and inspect for any damage. Keep all packaging materials until you are sure the fixture is in working order.

• Craftmade ZA3604-SA Canon Outdoor Wall Sconce Fixture
• Mounting Hardware (screws, wire nuts)
• Clear Glass Shade
• Instruction Manual

Note: Light bulb(s) and junction box are not included.

Setup and Installation

Before you begin, ensure you have the necessary tools: screwdriver, wire strippers, electrical tape, and safety glasses.

Step 1: Prepare for Installation

1. Turn off the electrical power at the main fuse or circuit breaker box.
2. Remove the old fixture from the wall, if applicable.
3. Unpack the new fixture and its components.

Step 2: Mount the Fixture

1. Attach the mounting plate (included) to the existing junction box (not included) using the provided screws. Ensure the plate is securely fastened.
2. Carefully pull the electrical wires from the junction box through the center hole of the mounting plate.

Step 3: Make Electrical Connections

Connect the wires according to the following. If your junction box has a ground wire (green or bare copper), connect it to the fixture's ground wire.

• Connect the black wire from the fixture to the black (hot) wire from the junction box.
• Connect the white wire from the fixture to the white (neutral) wire from the junction box.
• Connect the ground wire from the fixture (usually bare copper or green) to the ground wire from the junction box.

Secure all connections with wire nuts and wrap with electrical tape for added safety. Carefully tuck all wires into the junction box.

Step 4: Secure the Fixture Body

1. Align the fixture body with the mounting plate and secure it using the provided screws or nuts. Ensure the fixture is flush against the wall and stable.
2. Apply a weather-resistant sealant around the perimeter of the fixture where it meets the wall to prevent water entry, especially for outdoor installations.

Step 5: Install the Bulb and Glass Shade

1. Insert one 60-watt maximum A-type incandescent bulb (or equivalent CFL/LED) into the E26 medium base socket. Do not exceed the maximum wattage.
2. Carefully attach the clear glass shade to the fixture body according to the design. Ensure it is securely seated.

Image: The Craftmade ZA3604-SA Canon Outdoor Wall Sconce, featuring a satin aluminum finish and clear glass shade, shown in an installed outdoor setting.

Step 6: Restore Power

Once installation is complete, restore power at the main fuse or circuit breaker box and test the fixture.

Operating Instructions

The Craftmade ZA3604-SA Canon Outdoor Wall Sconce operates via a standard wall switch connected to your home's electrical system. Simply toggle the wall switch to turn the light on or off.

• Dimmable Feature: If a dimmable bulb (Incandescent, Dimmable CFL, or Dimmable LED) is installed and connected to a compatible dimmer switch (sold separately), you can adjust the light intensity.
• Control Method: The product specifications mention "App" as a control method. This typically refers to the ability to use smart bulbs (Wi-Fi or Bluetooth enabled) within the fixture, which can then be controlled via a smartphone app. The fixture itself does not have built-in smart capabilities.

Maintenance

Regular maintenance will help preserve the appearance and functionality of your Craftmade wall sconce.

• Cleaning: Turn off power before cleaning. Wipe the fixture with a soft, damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish. Clean the glass shade with a mild glass cleaner.
• Bulb Replacement: Ensure power is off and the bulb has cooled before attempting to replace it. Unscrew the old bulb and screw in a new E26 medium base bulb, not exceeding 60 watts.
• Inspection: Periodically inspect the fixture for any signs of wear, loose connections, or damage, especially in outdoor environments.

Troubleshooting

Specifications

• Model: ZA3604-SA
• Brand: Craftmade
• Dimensions (H x W): 10.13" x 5.5"
• Weight: Approximately 2.67 lbs
• Material: Aluminum (fixture), Glass (shade)
• Finish: Satin Aluminum
• Light Source: 1 x E26 Medium Base Bulb (not included)
• Max Wattage: 60 Watts (Incandescent)
• Compatibility: Incandescent, CFL, Halogen, LED bulbs
• Dimmable: Yes, with dimmable bulb and compatible dimmer switch
• Location Rating: WET Locations (Outdoor)
• Control Method: App (via smart bulb, if used)
• UPC: 647881218379

Warranty and Support

This Craftmade product is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Craftmade website. For technical support or assistance with installation, please contact Craftmade customer service.

Craftmade Official Website: www.craftmade.com

Please note: Warranty details are subject to change. Always refer to the most current information provided by the manufacturer.