Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Moen Lindor 84505BL single handle bathroom sink faucet. Please read all instructions carefully before beginning installation to ensure proper function and to prevent damage.
Safety Information
- Always turn off the main water supply before installing or servicing the faucet.
- Wear safety glasses during installation.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Do not overtighten connections, as this may cause damage.
Package Contents
Verify that all components are present before beginning installation:
- Moen Lindor 84505BL Faucet Assembly
- Pop-Up Drain Assembly
- Deck Plate (for 3-hole installations)
- Mounting Hardware
- Integrated Supply Lines
Setup and Installation
The Moen Lindor 84505BL faucet is designed for either 1-hole or 3-hole deck mount installations. For 3-hole installations, use the included deck plate.
Step 1: Prepare the Sink Area
Turn off the water supply at the shut-off valves under the sink or at the main water supply. Clear the area under the sink for access.
Step 2: Install the Faucet
Insert the faucet body through the hole(s) in the sink or countertop. If using the deck plate, ensure it is properly seated before placing the faucet. Secure the faucet from underneath the sink using the provided mounting hardware (washer and nut).
Image: The Moen Lindor 84505BL faucet with its matte black finish, installed on a white bathroom sink, demonstrating a typical deck-mount setup with the included deck plate.
Step 3: Connect Water Supply Lines
Connect the hot and cold water supply lines from the faucet to the corresponding shut-off valves. Hand-tighten first, then use a wrench for a quarter turn. Do not overtighten.
Step 4: Install the Drain Assembly
Follow the instructions provided with the pop-up drain assembly to install it into the sink drain hole. Ensure a watertight seal using plumber's putty or silicone sealant as directed.
Step 5: Test for Leaks
Once all connections are secure, slowly turn on the main water supply. Check all connections for leaks. Run the faucet for a few minutes to flush out any debris and check for proper operation.
Operating Instructions
The Moen Lindor 84505BL features a single handle for controlling both water flow and temperature.
- Water Flow: Lift the handle upwards to turn on the water and increase flow. Push the handle downwards to decrease flow and turn off the water.
- Temperature Control: Move the handle to the left for hot water and to the right for cold water. Adjust the handle position between left and right to achieve the desired water temperature.
- The faucet provides an aerated flow, which is suitable for daily bathroom tasks such as washing hands and brushing teeth.
Image: The Moen Lindor 84505BL faucet in operation, showing a steady stream of water flowing from the spout into the sink, illustrating its functional design.
Image: A person's hands being washed under the Moen Lindor 84505BL faucet, highlighting the practical use of the faucet in a bathroom environment.
Maintenance
Proper care will help maintain the finish and performance of your Moen faucet.
- Cleaning the Finish: Clean the matte black finish regularly with a soft, damp cloth. Avoid abrasive cleaners, harsh chemicals, or polishes, as these can damage the finish. For matte black finishes, daily cleaning may be required to remove water spots, soap residue, and toothpaste.
- Aerator Maintenance: If water flow decreases, the aerator may be clogged. Unscrew the aerator from the spout, clean any debris, and rinse thoroughly before reattaching.
- Handle Material: The handle is made of plastic. Clean gently with a soft cloth.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Flow | Clogged aerator; partially closed shut-off valves; debris in supply lines. | Clean the aerator. Ensure shut-off valves are fully open. Flush supply lines. |
| Leaks at Faucet Base | Loose mounting nut; improper sealant. | Tighten mounting nut. Reapply plumber's putty or silicone if necessary. |
| Leaks from Handle | Worn cartridge. | Contact Moen customer support for a replacement cartridge. |
| Water Temperature Issues | Incorrect supply line connection; water heater issues. | Verify hot and cold supply lines are connected correctly. Check water heater settings. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | Moen Lindor 84505BL |
| Brand | Moen |
| Finish Type | Matte Black |
| Material | Plastic (Handle), Metal (Body - typical for faucets) |
| Number of Handles | 1 |
| Hole Count | 1 (or 3 with deck plate) |
| Mounting Type | Deck Mount |
| Installation Type | Single Hole |
| Special Feature | Pop Up Drain |
| Spout Reach | 4.8 Inches |
| Product Dimensions | 3.5"D x 9"W x 21"H |
| Item Weight | 0.01 Ounces |
| UPC | 026508326077 |
| ADA Compliant | Yes |
Note: Product dimensions and item weight provided may represent shipping package details or be subject to minor variations. Refer to official Moen documentation for precise measurements.
Warranty Information
This Moen faucet is backed by a limited warranty. For specific details regarding coverage, duration, and terms, please refer to the warranty documentation included with your product or visit the official Moen website.
Warranty Type: Limited
Customer Support
For further assistance, technical support, or to order replacement parts, please contact Moen customer service or visit their official website:
- Brand: Moen
- Website: www.moen.com
- Model Number: 84505BL