Axton A601

Axton A601 6-Channel Digital Power Amplifier User Manual

Model: A601 | Brand: Axton

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Axton A601 6-Channel Digital Power Amplifier. The Axton A601 is designed to deliver high-quality audio performance in a compact form factor, featuring Class-D technology for efficiency and an aluminum heatsink for optimal heat dissipation. It is fully compatible with vehicles equipped with start/stop automatic systems.

Axton A601 6-Channel Digital Power Amplifier front view

Figure 1: Front view of the Axton A601 amplifier, showcasing its sleek, compact design.

2. Setup and Installation

Proper installation is crucial for optimal performance and safety. Ensure the vehicle's battery is disconnected before beginning installation.

2.1. Connections

Power Connections: Connect the +12V terminal to the positive terminal of the car battery via a fuse. Connect the GND terminal to a clean, unpainted metal point on the vehicle chassis. Connect the REM (Remote) terminal to the remote output of your head unit.
Input Connections: The amplifier supports both High-Level and Low-Level inputs. Use the appropriate input based on your head unit's output.
Speaker Outputs: Connect your speakers to the designated channels (CH1/2, CH3/4, CH5/6). The amplifier also supports bridged mode for higher power output to specific channels (e.g., subwoofers).

Axton A601 amplifier top view with power and speaker connections

Figure 2: Top view of the Axton A601, showing power, remote, ground, and speaker output terminals.

Axton A601 amplifier bottom view with input and control settings

Figure 3: Bottom view of the Axton A601, illustrating input connections and control knobs for sensitivity, crossover, and bass boost.

2.2. Initial Configuration

Input Mode: Select the correct input mode (High-Level or Low-Level) based on your connection type.
Turn-On Mode: The amplifier features Auto-Turn-On via DC-Offset or Music Signal, eliminating the need for a separate remote wire in some installations.
Crossover Settings: Adjust the integrated electronic crossover filters (LPF for subwoofers, HPF for satellites) to optimize sound reproduction for your speaker setup.
- 12 dB/Oct. Low-Pass Filter (Subwoofer): 50 – 300 Hz
- 12 dB/Oct. High-Pass Filter (Satellites): 50 Hz
Sensitivity (Gain): Set the input sensitivity to match the output voltage of your head unit. Start with the minimum setting and gradually increase until desired volume is achieved without distortion.
Bass Boost Control: Adjust the bass boost at 45 Hz (0 – 12 dB) to enhance low-frequency response.

3. Operating Instructions

Once installed and configured, the Axton A601 operates automatically with your vehicle's audio system.

Power On/Off: The amplifier will power on automatically when it receives a signal (either remote, DC-offset, or music signal) and power off when the signal is removed.
Audio Playback: Play audio through your head unit. Adjust the volume and tone controls on your head unit as usual.
Bass Level Remote Control: Use the included bass level remote control to conveniently adjust the subwoofer output level from your listening position.

4. Maintenance

To ensure the longevity and optimal performance of your Axton A601 amplifier, follow these simple maintenance guidelines:

Cleaning: Regularly wipe the amplifier's exterior with a soft, dry cloth to remove dust and dirt. Do not use liquid cleaners or solvents.
Ventilation: Ensure that the amplifier's heatsink fins are not obstructed. Proper airflow is essential for heat dissipation.
Connections: Periodically check all power, ground, remote, and speaker connections to ensure they are secure and free from corrosion. Loose connections can lead to performance issues or damage.
Environment: Avoid exposing the amplifier to excessive moisture, direct sunlight, or extreme temperatures.

5. Troubleshooting

If you experience issues with your Axton A601 amplifier, consult the following troubleshooting guide before seeking professional assistance.

Problem	Possible Cause	Solution
No Power / Amplifier does not turn on	Blown fuse Loose power or ground connection No remote signal Incorrect Auto-Turn-On setting	Check and replace fuse if necessary Verify all power, ground, and remote connections are secure Ensure head unit's remote output is active Adjust Auto-Turn-On mode (DC-Offset/Music Signal)
No Sound Output	Input cables disconnected or faulty Speaker wires disconnected or shorted Gain setting too low Crossover settings incorrect	Check RCA or high-level input cables Inspect speaker wiring for proper connection and shorts Increase gain (sensitivity) gradually Verify LPF/HPF settings are appropriate for your speakers
Distorted Sound / Noise	Gain set too high Poor ground connection (ground loop) Speaker impedance mismatch Interference from vehicle's electrical system (e.g., alternator noise)	Reduce gain setting Ensure ground connection is clean and secure Verify speaker impedance matches amplifier's capabilities Reroute power/RCA cables away from vehicle wiring; consider a ground loop isolator if noise persists
Amplifier Overheating	Insufficient ventilation Speaker impedance too low Excessive volume for prolonged periods	Ensure amplifier is mounted in a well-ventilated area Check speaker impedance; ensure it's within amplifier's rated range Reduce volume or allow amplifier to cool down

6. Specifications

Detailed technical specifications for the Axton A601 6-Channel Digital Power Amplifier:

Feature	Specification
Model Number	A601
Number of Channels	6
Output Power @ 4 Ohm	6 x 100 W
Output Power @ 2 Ohm	6 x 160 W
Output Power @ 4 Ohm Bridged	3 x 320 W
Frequency Response	10 Hz – 21 kHz
Signal-to-Noise Ratio	>86 dB
Variable Input Sensitivity	0.5 – 12 V
Integrated Electronic Crossover	12 dB/Oct. LPF (50 – 300 Hz), 12 dB/Oct. HPF (50 Hz)
Bass Boost Control	@ 45 Hz (0 – 12 dB)
Dimensions (W x H x D)	282 x 40 x 105 mm
Voltage	10 Volts
Material	Aluminum
Compliance	CE

Axton A601 manual page with detailed technical specifications table

Figure 4: Excerpt from the official manual, detailing the technical specifications of the Axton A601 amplifier.

7. Warranty and Support

Warranty information for the Axton A601 amplifier is not provided in this manual. For detailed warranty terms, technical support, or service inquiries, please refer to the manufacturer's official website (www.axton.de) or contact your authorized Axton retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.