Midea NTH20-17BR Ceramic Fan Heater User Manual

1. Introduction

Thank you for choosing the Midea NTH20-17BR Ceramic Fan Heater. This manual provides important information for the safe and efficient operation, maintenance, and troubleshooting of your new appliance. Please read it thoroughly before use and retain it for future reference.

2. Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using this heater.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 1 meter (3 feet) from the front of the heater and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
• Always unplug heater when not in use.
• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
• Do not use outdoors.
• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
• To disconnect heater, turn controls to OFF, then remove plug from outlet.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
• This heater includes an overheat protection sensor that automatically shuts off the unit if it detects excessive temperatures.

Image: Illustration of the overheat protection feature, showing a thermometer indicating high temperature and a shield icon with flames, signifying enhanced safety.

3. Product Overview

The Midea NTH20-17BR is a ceramic fan heater designed for efficient and comfortable heating. It features PTC ceramic heating technology for rapid warmth, multiple operating modes, oscillation for even heat distribution, and a 24-hour timer.

3.1 Components

• Main Unit (Heater Body)
• Control Panel (Top)
• Air Outlet Grille (Front)
• Air Inlet Grille (Rear, with filter)
• Power Cord
• Remote Control
• Safety Tip-over Switch (Bottom)

Image: Front view of the Midea NTH20-17BR ceramic fan heater, showcasing its sleek design and grille.

3.2 Control Panel and Display

The heater features an intuitive control panel located on the top of the unit and an LED display for easy monitoring of settings.

Image: Close-up of the heater's top control panel with an LED display, showing touch buttons for ON/OFF, Mode, Timer, Oscillation, Temperature Up, and Temperature Down.

4. Setup

Follow these steps for initial setup:

1. Unpacking: Carefully remove the heater from its packaging. Retain the packaging for storage or future transport.
2. Placement: Place the heater on a firm, level surface. Ensure there is at least 1 meter (3 feet) of clear space around the heater from walls, furniture, and other objects to allow for proper airflow and prevent fire hazards. Do not place it directly under a power outlet. The heater can be used vertically or horizontally.

Image: The Midea NTH20-17BR heater shown in a horizontal position on the floor, demonstrating its flexible placement options.

3. Power Connection: Plug the power cord directly into a grounded 220-240V AC, 50Hz electrical outlet. Do not use extension cords or power strips.

5. Operating Instructions

The heater can be operated using the touch control panel on the unit or the included remote control.

5.1 Power On/Off

• Press the ON/OFF button on the control panel or remote control to turn the heater on or off.

5.2 Mode Selection

Press the Mode (M) button to cycle through the available operating modes:

• High Heat (2000W): Provides maximum heating power.
• Low Heat (1200W): Provides moderate heating power.
• ECO Mode: The heater automatically adjusts the heating power (between 1200W and 2000W) based on the ambient room temperature to maintain the set temperature efficiently. This mode helps save energy.
• Fan Mode: Operates as a fan without heating, circulating air.

5.3 Temperature Setting

In High, Low, or ECO modes, use the Temperature + and Temperature - buttons on the control panel or remote control to set your desired room temperature. The LED display will show the set temperature.

5.4 Oscillation Function

Press the Oscillation button on the control panel or remote control to activate or deactivate the oscillation feature. When active, the heater will rotate from side to side to distribute warm air more widely and evenly across the room.

5.5 Timer Function

The heater features a 24-hour timer:

• Press the Timer button on the control panel or remote control.
• Each press will increase the timer setting by 1 hour, up to 24 hours.
• The timer can be set to automatically turn the heater off after the selected duration.

5.6 Remote Control

The included remote control allows for convenient operation from a distance. Ensure the remote control has working batteries and is pointed towards the heater's receiver.

Image: A hand holding the wireless remote control for the Midea NTH20-17BR heater, showing its various function buttons.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your heater.

6.1 Cleaning

• Always unplug the heater and allow it to cool completely before cleaning.
• Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Do not immerse the heater in water or allow water to drip into the interior.

6.2 Anti-Dust Filter Cleaning

The heater is equipped with an anti-dust filter to prevent dust accumulation. This filter should be cleaned regularly.

• Locate the air inlet grille at the rear of the heater.
• Carefully remove the filter from its housing.
• Clean the filter using a vacuum cleaner or by rinsing it gently under running water. Ensure the filter is completely dry before reinserting it.
• Reinstall the filter into the air inlet grille.

Image: Diagram showing the removal and cleaning process for the anti-dust filter located at the rear of the Midea NTH20-17BR heater.

6.3 Storage

When storing the heater, keep it in a cool, dry place. It is recommended to store it in its original packaging to protect it from dust and damage.

7. Troubleshooting

If your heater is not operating correctly, please check the following common issues before contacting customer support:

8. Specifications

Image: Diagram illustrating the dimensions of the Midea NTH20-17BR ceramic fan heater: 17.4 cm (depth), 16 cm (width), and 55.09 cm (height).

9. Warranty and Support

Midea products are manufactured to high-quality standards. For warranty information, please refer to the warranty card included with your purchase or contact Midea customer support. Keep your proof of purchase for any warranty claims.

For technical support or service inquiries, please visit the official Midea website or contact their customer service department in your region.