1. Introduction
This manual provides essential instructions for the safe and efficient use of your APC 2200VA Line Interactive UPS, model BVX2200LI-IN. Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage to the unit or connected equipment. Keep this manual for future reference.
Figure 1: Front view of the APC 2200VA Line Interactive UPS BVX2200LI-IN. This image displays the front panel of the UPS, featuring the power button, status indicators, and a USB charging port.
2. Safety Information
Observe the following safety precautions to reduce the risk of electric shock, fire, or injury:
- Do not open the UPS enclosure. There are no user-serviceable parts inside.
- Do not operate the UPS in direct sunlight, near heat sources, or in areas with excessive dust, moisture, or corrosive substances.
- Ensure the UPS is connected to a properly grounded AC power outlet.
- Do not connect non-computer related equipment, such as medical devices, life support equipment, microwave ovens, or vacuum cleaners, to the UPS.
- Disconnect the UPS from the power outlet before cleaning. Use a dry cloth for cleaning.
3. Setup and Installation
3.1 Unpacking and Inspection
Carefully unpack the UPS and inspect it for any shipping damage. If any damage is found, notify the carrier and your dealer. The package should contain the UPS unit and this user manual.
3.2 Battery Connection
Before initial use, the internal battery must be connected. Refer to the diagram below for detailed steps:
Figure 2: BVX Start-up Settings - Battery Connection. This diagram illustrates the four steps to properly connect the internal battery: pull, rotate, push, and lock the yellow battery connector into its seating.
- Pull the battery connector from its seating.
- Rotate the battery connector.
- Push the battery connector into the slot until it locks in position.
- Once locked, the battery connector is ready-to-use.
3.3 Connecting to Power and Devices
Connect the UPS power cord directly into a wall outlet. Note that this UPS requires a 3-pin 16A adapter or a 16A 3-pin power outlet due to its larger plug size. Connect your computer, monitor, router, and other critical electronic devices to the outlets on the rear of the UPS.
Figure 3: Rear view of the APC 2200VA Line Interactive UPS. This image shows the back panel of the UPS, including multiple power outlets for connecting devices, the input power cord, and the battery connector port.
4. Operation
4.1 Turning On the UPS
Press the POWER ON/OFF button on the front panel to turn on the UPS. The green Power ON LED will illuminate, confirming that the UPS is operational and providing protection.
The UPS battery charges to full capacity during the first 24 hours while connected to utility power. The UPS will charge the battery whether it is turned on or off. Do not expect the battery to provide its full rated backup time during this initial charging period.
4.2 Turning Off the UPS
Press and hold the POWER ON/OFF button for more than 2 seconds to turn off the UPS. A 2-second delay is incorporated to prevent accidental power-off.
4.3 Automatic Voltage Regulation (AVR)
The Line Interactive UPS features Automatic Voltage Regulation (AVR). This function automatically corrects minor voltage fluctuations (sags and surges) without switching to battery power, thereby preserving battery life and ensuring a stable power supply to connected devices.
4.4 USB Charging Port
The front panel includes a USB charging port (5V 2A) for convenient charging of mobile devices, even during a power outage when the UPS is operating on battery power.
Figure 4: UPS with USB Charging. This image shows the APC UPS on a desk, with a smartphone connected to its front USB port for charging, demonstrating its utility for mobile devices.
5. Maintenance
5.1 Battery Care
The UPS contains a sealed lead-acid battery with an average expected life of 5 years under normal operating conditions. Factors such as frequent power outages, high temperatures, and deep discharges can reduce battery life. It is recommended to periodically test the UPS by simulating a power outage to ensure the battery is functioning correctly.
5.2 Cleaning
To clean the exterior of the UPS, disconnect it from the power source and use a soft, dry cloth. Do not use liquid or aerosol cleaners, as they may contain flammable substances or cause electrical shock.
5.3 Environmental Conditions
Operate the UPS in a clean, dry, and well-ventilated area. Avoid placing it near windows or in environments with high humidity, extreme temperatures, or direct sunlight, as these conditions can negatively impact performance and battery longevity.
6. Troubleshooting
If the UPS is not operating correctly, consult the following table for common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| UPS does not turn on. | Battery not connected or discharged. | Ensure the internal battery connector is fully seated. Plug the UPS into a wall outlet and allow it to charge for at least 24 hours. |
| Short backup time. | Battery not fully charged or nearing end of life. Overloaded UPS. | Allow the UPS to charge for 24 hours. Reduce the load on the UPS. If the battery is old, consider replacement. |
| Continuous beeping with no lights. | Indicates a potential battery failure or critical internal fault. | Disconnect all loads and turn off the UPS. Contact APC customer support for assistance. |
| UPS not providing power to outlets. | Circuit breaker tripped. UPS is off. | Check the circuit breaker on the rear of the UPS and reset if tripped. Ensure the UPS is turned on. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | APC |
| Model Number | BVX2200LI-IN |
| Capacity | 2200VA |
| Type | Line Interactive UPS |
| Input Voltage | 2200 Volts (Nominal) |
| Battery Type | Sealed Lead Acid |
| Battery Charge Time | 6 Hours (to 90% capacity) |
| Average Battery Life | 5 Years |
| Product Dimensions (LxWxH) | 14 x 39 x 19 cm |
| Item Weight | 12.2 kg |
| Form Factor | Rack |
| Color | Black |
| Country of Origin | China |
Note: While the specifications list "Rack" form factor, the product images and typical usage for this model suggest a tower form factor.
8. Warranty and Support
This APC UPS is manufactured by Schneider Electric. For detailed warranty information, product registration, and technical support, please visit the official APC by Schneider Electric website or contact their customer service department.
When contacting support, please have your model number (BVX2200LI-IN) and serial number ready. Be aware that customer support availability may vary, and it is advisable to check their operating hours for prompt assistance.
Manufacturer: APC, SCHNEIDER ELECTRIC, 1,2.3,4 BUILDINC WORKSHOP, HENGCHANCRONC INDUSl'RIAL PARK, SHILONC COMMUNIl'Y STIIYAN 51'RI'I]T. BAOAN DISTRICT' SHENZFIEN. CHINA 5 I 8I08
