1. Introduction
This instruction manual provides essential information for the safe and effective use of your HZPOWEN 6V Kids Powered Ride-On Car Battery Charger. Please read this manual thoroughly before operating the charger and retain it for future reference. This charger is designed to provide a reliable power source for various 6-volt ride-on toys.
2. Safety Information
To ensure safe operation and prevent damage, observe the following safety precautions:
- This charger is designed for 6-volt batteries only. Do not use with batteries of different voltages.
- Ensure the charger's output connector (red) matches the input port of your ride-on toy's battery.
- The charger features built-in protections: Over-Voltage Protection, Over-Current Protection, Short-Circuit Protection, and Over Temperature Protection. These features prevent overcharging and damage to the battery and charger.
- Do not expose the charger to water or excessive moisture.
- Do not operate the charger if it has been damaged in any way.
- Keep the charger away from children.
- Always unplug the charger from the wall outlet before disconnecting it from the battery.
- Use the charger in a well-ventilated area.
Image: HZPOWEN charger highlighting its multiple protection features including over-load, short circuit, over-charge, over-voltage, and temperature protection.
3. Setup and Connection
Follow these steps to connect your charger:
- Ensure the ride-on toy is turned off.
- Locate the charging port on your 6-volt ride-on toy. This charger is designed to fit 6-volt batteries with a "RED" connector.
- Connect the red output connector of the HZPOWEN charger to the charging port of the ride-on toy. Ensure a secure connection.
- Plug the charger's AC power cord into a standard 100-240Vac 50/60Hz wall outlet.
Image: The HZPOWEN 6V charger showing its main unit and the red connector for the ride-on toy battery.
Image: Front view of the HZPOWEN 6V charger, displaying input (100-240Vac, 0.45A MAX, 50/60Hz) and output (7.0V, 0.8A) specifications, along with safety certifications.
4. Operating Instructions
Once connected, the charger will begin charging the battery. Observe the LED indicator for charging status:
- Red LED: Indicates the battery is currently charging.
- Green LED: Indicates the battery is fully charged and ready for use.
Disconnect the charger once the LED turns green. It is recommended to charge the battery for the duration specified by your ride-on toy's manufacturer, typically 8-12 hours for a full charge, or until the green LED illuminates.
5. Maintenance
Proper maintenance ensures the longevity and performance of your charger:
- Keep the charger clean and dry. Wipe with a soft, dry cloth.
- Store the charger in a cool, dry place when not in use.
- Avoid wrapping the cord too tightly around the charger to prevent damage to the wiring.
- Regularly inspect the charger and its cables for any signs of damage. If damage is found, discontinue use and replace the charger.
6. Troubleshooting
If you encounter issues with your charger, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger LED does not light up. | No power from outlet, loose connection, or faulty charger. | Check wall outlet with another device. Ensure charger is securely plugged into both the wall and the ride-on toy. If problem persists, the charger may be faulty. |
| LED remains red after extended charging. | Battery not fully charged, or battery issue. | Allow more time for charging (up to 12 hours). If the LED never turns green, the ride-on toy's battery may be old or damaged and require replacement. |
| Charger gets warm during use. | Normal operation. | A slight warmth is normal. If the charger becomes excessively hot, disconnect immediately and contact support. |
| Charger connector does not fit. | Incompatible connector type. | This charger is designed for 6-volt batteries with a "RED" connector. Verify your ride-on toy's charging port. |
7. Specifications
- Model: 6V Ride-On Car Battery Charger
- Input: 100-240Vac, 0.45A MAX, 50/60Hz
- Output: 7.0V, 0.8A
- Compatibility: Designed for 6-volt batteries with "RED" connector.
- Certifications: CE / FCC Certified
- Protection Features: Over-Voltage, Over-Current, Short-Circuit, Over Temperature Protection
- Cable Length: Approximately 5 feet (1.5 meters)
- Dimensions: Approximately 4.76 x 2.2 x 1.3 inches (Charger unit)
- Weight: Approximately 2.47 ounces (0.15 lbs)
Image: The HZPOWEN 6V charger illustrating its approximate 5-foot total cable length.
8. Compatible Ride-On Toys
This charger is compatible with various 6-volt ride-on toys that utilize a "RED" connector, including but not limited to:
- Kid Trax Disney Princess Toddler Quad
- Kid Trax Frozen 2 Toddler Quad
- Kid Trax Disney Frozen 4x4
- Kid Trax Disney Mickey Mouse Quad
- Moto Trax Toddle Quad
- Mickey Mouse Sidecar Scooter
- Rollplay BMW i8 (Note: Not for Dynacraft BMW i8)
- Rollplay VW Beetle
- Rollplay VW Bus
- Rollplay Mini Audi R8 Spyder
- Rollplay BMW X5
- Avigo Mini Quad
- Chevy Silverado
- Chevy Silverado Police Truck
- Chevy Tahoe Police SUV
- GMC Sierra
- GMC Yukon Denali Fire Rescue
- Huffy BMW X6
Always verify the voltage and connector type of your ride-on toy before use.
9. Warranty and Support
For warranty information or technical support, please contact HZPOWEN customer service. Refer to the product packaging or the seller's information for contact details. Keep your purchase receipt as proof of purchase.
