Introduction
Thank you for choosing the Ferm 20 Volt 1.5 Ah Cordless Drill/Driver. This manual provides comprehensive instructions for the safe and efficient operation, maintenance, and troubleshooting of your new tool. Designed for versatility, this aluminum drill/driver features a 6 mm drilling function, making it ideal for various home and workshop tasks. Please read this manual thoroughly before first use and keep it for future reference.
Safety Instructions
Always observe basic safety precautions when using electrical tools to reduce the risk of fire, electric shock, and personal injury.
- Work Area Safety: Keep your work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Electrical Safety: Avoid body contact with earthed or grounded surfaces. Do not expose power tools to rain or wet conditions.
- Personal Safety: Always wear eye protection. Use hearing protection when operating for extended periods. Dress properly; avoid loose clothing or jewelry.
- Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
- Battery Pack Safety: Recharge only with the charger specified by the manufacturer. Do not disassemble, open, or shred battery packs. Do not expose battery packs to heat or fire.
Product Overview
Familiarize yourself with the components of your Ferm Cordless Drill/Driver.
Figure 1: Front view of the Ferm 20 Volt 1.5 Ah Cordless Drill/Driver. This image shows the main body of the drill, including the chuck, torque setting ring, speed selector, trigger, and the attached 20V 1.5Ah battery pack.
Figure 2: The Ferm Cordless Drill/Driver alongside its battery charger. This image illustrates the complete package, including the drill with its battery and the separate charging unit with its power cable.
Figure 3: The durable black carrying case for the Ferm Cordless Drill/Driver. This image shows the compact and robust case designed for protecting and transporting the tool and its accessories.
Setup
Charging the Battery
- Connect the charger to a standard power outlet.
- Insert the battery pack into the charger. Ensure it clicks into place.
- The charging indicator light on the charger will illuminate (refer to charger manual for specific light indications).
- Once fully charged, remove the battery from the charger.
Note: Fully charge the battery before first use. The battery is a 20 Volt Lithium-ion type.
Installing/Removing Drill Bits
- Ensure the drill is switched off and the battery pack is removed for safety.
- Rotate the chuck counter-clockwise to open the jaws.
- Insert the drill bit or screwdriver bit into the chuck, ensuring it is centered.
- Rotate the chuck clockwise to tighten the jaws securely around the bit.
- To remove, rotate the chuck counter-clockwise until the jaws open, then pull out the bit.
Operating
Powering On/Off
- To turn on, press the trigger switch. The speed increases with pressure.
- To turn off, release the trigger switch.
Forward/Reverse Rotation
The forward/reverse selector switch is located above the trigger. Push it to the left for forward rotation (for drilling and tightening screws) and to the right for reverse rotation (for loosening screws).
Torque Setting
The torque setting ring is located behind the chuck. Rotate it to select the desired torque level. Lower settings are for driving small screws or working with soft materials, while higher settings are for larger screws or harder materials. The drill also has a dedicated drilling mode for maximum power without clutch engagement.
Drilling and Screwdriving Tips
- Always hold the tool firmly with both hands.
- Apply steady, even pressure. Do not force the drill.
- For drilling, start with a pilot hole if necessary, especially in hard materials.
- For screwdriving, ensure the bit is fully seated in the screw head to prevent stripping.
Maintenance
Cleaning
- Regularly clean the ventilation slots of the tool to prevent overheating.
- Use a soft, damp cloth to wipe down the exterior. Do not use harsh chemicals or abrasive cleaners.
- Keep the chuck jaws free of dust and debris.
Storage
- Store the drill/driver and battery pack in a cool, dry place, away from direct sunlight and moisture.
- If storing for extended periods, ensure the battery is partially charged (around 50%) to prolong its lifespan.
- Store the tool in its original carrying case for protection.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Drill does not start. | Battery not charged or not properly inserted. | Charge battery. Ensure battery is fully seated. |
| Loss of power during operation. | Battery low or overloaded. | Recharge battery. Reduce pressure on the tool. |
| Bit slips in chuck. | Chuck not tightened sufficiently or bit shank is dirty. | Tighten chuck firmly. Clean bit shank. |
| Overheating. | Blocked ventilation slots or continuous heavy use. | Clean ventilation slots. Allow tool to cool down. |
Specifications
- Brand: Ferm
- Model: 20 Volt 1.5 Ah Cordless Drill/Driver
- Voltage: 20 Volt
- Battery Type: Lithium-ion (1.5 Ah)
- Chuck Size (Max): 6 Millimeter
- Material: Aluminum
- Power Source: Battery Powered
Warranty and Support
Ferm products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. For detailed warranty information, service, or technical support, please refer to the warranty card included with your product or visit the official Ferm website. Please retain your proof of purchase for any warranty claims.
For further assistance, you may contact Ferm customer service through their official channels. Always provide your product model number and purchase details when seeking support.
