1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your KES XB6240-BK Tub and Shower Faucet System. This system features a 10-inch rain shower head and a waterfall tub faucet, designed for wall-mount installation. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Safety Information
Observe all local plumbing and building codes. Professional installation is recommended. Ensure water supply is turned off before beginning installation. Wear appropriate personal protective equipment (PPE) during installation. This product is designed for residential use. Do not modify the product as this may void the warranty and create safety hazards.
Warning: To prevent scalding, ensure the pressure-balanced valve is correctly installed and calibrated according to instructions. Test water temperature before use.
3. Included Components
Verify that all parts are present before beginning installation. If any parts are missing or damaged, contact KES customer support for replacements.
Figure 3.1: Parts List for KES XB6240-BK Shower System.
- Showerhead (10", SUS304 Stainless Steel)
- Diverter Knob & Handle
- Cover Plate
- Pressure Balance Valve (Brass, Anti-Scalding)
- Waterfall Tub Faucet
- Shower Arm & Escutcheon
- Gloves
- Installation Guide (this document)
- Other Accessories (mounting hardware, seals, etc.)
4. Setup and Installation
Installation should be performed by a qualified professional. Refer to the provided diagram for recommended dimensions and rough-in specifications.
Figure 4.1: Product Dimensions and U.S. Standard Connections.
4.1 Pre-Installation Steps
- Turn off the main water supply to the bathroom.
- Clear the installation area and ensure you have all necessary tools.
- Review local plumbing codes and ensure compliance.
4.2 Valve Installation
- Install the pressure balance valve (4) into the wall according to the rough-in dimensions shown in Figure 4.1.
- Connect the hot and cold water lines to the appropriate inlets on the valve.
- Connect the outlet lines to the shower arm and tub spout locations.
- Ensure all connections are secure and watertight.
- The valve is designed to prevent scalding by balancing hot and cold water pressure.
4.3 Shower Head and Arm Installation
- Install the shower arm (6) into the wall outlet, ensuring it is securely fastened.
- Attach the 10-inch showerhead (1) to the shower arm. Hand-tighten, then use a wrench for a final quarter turn, being careful not to overtighten.
- The showerhead features self-cleaning nozzles and a 360° rotation for adjustable angle.
4.4 Tub Spout Installation
- Install the waterfall tub faucet (5) onto the wall outlet.
- Ensure the tub spout is level and securely attached to prevent leaks.
4.5 Final Steps
- Install the cover plate (3) and the diverter knob and handle (2) onto the valve.
- Turn on the main water supply and check for any leaks.
- Test the functionality of both the shower head and tub spout.
5. Operating Instructions
Your KES shower system is designed for ease of use and offers simultaneous operation of the shower head and tub spout.
Video 5.1: Demonstration of KES Tub and Shower Faucet Set operation, showing how to switch between the waterfall tub spout and the rain shower head, and adjust water temperature.
5.1 Water Flow Control
- The upper knob on the valve trim controls the water flow to either the shower head or the tub spout.
- Rotate the knob to select your desired water outlet.
- The system allows for both the shower head and tub spout to run simultaneously.
5.2 Temperature Adjustment
- The lower handle on the valve trim controls the water temperature.
- Move the handle to adjust the mix of hot and cold water.
- The pressure-balanced valve maintains a consistent water temperature, preventing sudden changes due to pressure fluctuations elsewhere in the plumbing system.
Figure 5.2: Pressure-balanced valve with anti-scald cartridge.
6. Maintenance
6.1 Cleaning
- Clean the faucet and shower head regularly with a soft cloth and mild soap or a non-abrasive cleaner.
- Avoid using abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the matte black finish.
- The shower head features self-cleaning silicone nozzles. Gently rub the nozzles to dislodge any mineral buildup.
Figure 6.1: Shower head with self-cleaning nozzles.
6.2 Long-Term Care
- Periodically check all connections for tightness and signs of wear.
- If you experience reduced water flow, check the shower head nozzles for mineral buildup and clean as described above.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Pressure | Clogged shower head nozzles or mineral buildup. | Clean the silicone nozzles on the shower head by gently rubbing them. Check water supply valves for full opening. |
| Water Temperature Fluctuations | Pressure balance valve not functioning correctly or external plumbing issues. | Ensure the pressure balance valve is correctly installed. If issues persist, consult a professional plumber. |
| Leaks from Connections | Loose connections or damaged seals. | Turn off water supply. Tighten connections. Replace any worn or damaged seals. |
| Pipe Noise (Water Hammer) | Air in pipes or high water pressure. | The KES valve is designed to minimize pipe noise. If noise occurs, consult a plumber to check for air in the system or excessive water pressure. |
8. Specifications
- Model Number: XB6240-BK
- Brand: KES
- Color: Matte Black
- Material: Stainless Steel (SUS304 for shower head), Brass (Rough-in Valve)
- Finish Type: Black
- Number of Handles: 2
- Mounting Type: Wall Mount
- Shower Head Size: 10 inches
- Flow Rate: 1.8 GPM (Gallons Per Minute), 6.8 L/min at 80 PSI
- Maximum Pressure: 5.5 Bars
- Product Dimensions: 15.8 x 13.4 x 6.7 inches
- Item Weight: 9.1 Pounds
- Installation Method: Wall-Mounted
- Included Components: 10" Shower Head, Rough-in Valve with Trim, Shower Arm, Waterfall Style Tub Spout, Other Accessories
9. Warranty and Support
9.1 Warranty Information
This KES product is covered by a Lifetime Limited Warranty. Please refer to the official KES website or contact customer support for full details regarding warranty terms and conditions.
9.2 Customer Support
For any questions, technical assistance, or replacement parts, please contact KES customer support. Our team is available 24/7 to assist you.
- Replacement Parts: Free replacement parts are available upon request if any parts are damaged or missing.
- 1-on-1 Exclusive Service: Professional support is available to follow up on individual cases efficiently.
For more information, visit the KES Store on Amazon.
