1. Introduction
This manual provides detailed instructions for the assembly, use, and maintenance of your Teraves Dining Table Set for 4. This versatile 4-piece set includes one table, two chairs, and one bench, designed for various uses such as dining, computer work, or as an office desk. Please read these instructions carefully before assembly and use to ensure safe and proper operation.
2. Safety Information
Warning: To prevent tipping, this furniture must be anchored to the wall or floor using the provided hardware. Always ensure all screws and fasteners are securely tightened before use.
3. Package Contents
Please verify that all components are present before beginning assembly. If any parts are missing or damaged, please contact customer support.
- 1 x Dining Table
- 2 x Dining Chairs
- 1 x Dining Bench
- Assembly Hardware (screws, bolts, Allen wrench)
- Instruction Manual (this document)
4. Assembly Instructions
Assembly is designed to be straightforward. It is recommended to have two people for assembly. Please follow these steps carefully.
4.1 Tools Required
- Included Allen Wrench
- Phillips Head Screwdriver (not always included, but useful)
4.2 Step-by-Step Assembly
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Assemble the Table Frame: Attach the table legs to the table frame using the provided screws and Allen wrench. Do not fully tighten screws until all components are aligned.
- Attach Tabletop: Secure the tabletop to the assembled frame. Ensure all holes align before tightening screws.
- Assemble Chairs: Attach the chair legs to the chair seats and backrests. Pay attention to the orientation of the backrests. Important: Use the correct length screws for the bench to avoid damage.
- Assemble Bench: Attach the bench legs to the bench seat. Ensure the lower storage rack is properly installed if applicable.
- Final Tightening: Once all pieces are assembled and aligned, go back and fully tighten all screws and bolts on the table, chairs, and bench.
- Wall Anchoring: For safety, anchor the table to a wall using the provided anti-tip hardware.
Figure 1: Fully assembled Teraves Dining Table Set in a dining room.
5. Usage and Operation
Your Teraves Dining Table Set is designed for versatility and can serve multiple functions in your home.
- Dining Area: Use as a primary dining table for up to four people. The bench provides flexible seating.
- Workstation: The table can function as a computer desk, office desk, or writing workstation.
- Space-Saving Design: The chairs and bench can be tucked neatly under the table when not in use, optimizing space in smaller areas.
Figure 2: The dining table set configured as a computer desk.
Figure 3: Illustration of the space-saving design, showing how the chairs and bench fit under the table.
6. Maintenance and Care
Proper care will extend the life and appearance of your dining set.
- Cleaning: Wipe surfaces with a dry cloth. Avoid abrasive cleaners or harsh chemicals that may damage the finish.
- Spills: Clean spills immediately with a dry or slightly damp cloth to prevent staining.
- Heat Protection: Use coasters or placemats to protect the tabletop from hot items.
- Regular Checks: Periodically check and tighten all screws and bolts to ensure stability and safety.
Figure 4: Detail of the waterproof wood board and rounded corner design, highlighting durability.
7. Troubleshooting
If you encounter any issues during assembly or use, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Table/Chair/Bench is wobbly | Screws are not fully tightened or components are misaligned. | Loosen all screws slightly, adjust the component to ensure it sits flat, then retighten all screws firmly. Ensure all legs are level. |
| Missing parts or damaged components | Packaging error or transit damage. | Contact customer support with your purchase details and a description of the missing/damaged parts. |
| Difficulty aligning screw holes | Components are not correctly oriented or screws are overtightened prematurely. | Ensure all parts are oriented as shown in the assembly diagrams. Do not fully tighten screws until all parts are loosely assembled. |
8. Specifications
- Brand: Teraves
- Model: B08N4FD96H
- Color: Teak
- Material: Medium Density Fiberboard (MDF) and Steel Frame
- Style: Modern
- Assembly Required: Yes
- Table Dimensions: 43.3''L x 27.56''W x 29.92''H (110cm L x 69.6cm W x 75cm H)
- Chair Dimensions: 15.35''L x 17.72''W x 33.86''H (40cm L x 40cm W x 86.6cm H)
- Bench Dimensions: 33.46''L x 14.17''W x 18.11''H (85cm L x 36cm W x 46cm H)
- Unit Count: 4.0 Count (1 table, 2 chairs, 1 bench)
Figure 5: Dimensional diagram of the Teraves Dining Table Set components.
9. Warranty and Support
Teraves products are manufactured to high-quality standards. For warranty information or customer support, please refer to your purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.
Return Policy: This product typically includes a 30-day return/replacement policy. Please check with your retailer for specific terms.
