1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your Pureit Hul Copper+ Eco Mineral RO+UV+MF Water Purifier. This advanced system is designed to provide purified water through a 7-stage purification process, enriching it with the goodness of copper and offering high water saving capabilities.
Image: Front view of the Pureit Hul Copper+ Eco Mineral RO+UV+MF Water Purifier, showcasing its black and copper design.
2. Important Safety Instructions
Please read all safety instructions carefully before operating the appliance to prevent injury or damage.
- Ensure the purifier is installed by a qualified technician.
- Do not immerse the appliance, cord, or plug in water or other liquids.
- Keep the appliance away from direct sunlight, heat sources, and corrosive chemicals.
- Do not allow children to operate the purifier without supervision.
- Use only potable water as input. The maximum supported TDS level is 500 PPM.
- Unplug the appliance before cleaning or performing any maintenance.
3. What's in the Box
Upon unpacking, verify that all components are present and undamaged:
- 1 x Pureit Hul Copper+ Eco Mineral RO+UV+MF Water Purification Unit
4. Installation Guide
The Pureit WUCU200 is a freestanding unit. Professional installation is recommended.
- Choose a Location: Select a clean, dry, and well-ventilated area near a water source and an electrical outlet. Ensure sufficient space around the unit for maintenance.
- Water Connection: Connect the purifier to the raw water supply as per the installation diagram provided by the technician. Ensure all connections are secure to prevent leaks.
- Drain Connection: Connect the waste water pipe to a suitable drain.
- Power Connection: Plug the power cord into a grounded electrical outlet. The purifier operates on a MANUAL power source.
- Initial Flush: Before first use, allow the purifier to run for a few cycles to flush out any manufacturing residues. Refer to the technician's instructions for the specific flushing procedure.
Image: The Pureit water purifier positioned in a kitchen environment, illustrating typical placement.
5. Operating Instructions
Follow these steps for daily operation of your water purifier:
- Power On: Ensure the purifier is plugged in and the power switch (if present) is turned on. Indicator lights will illuminate, showing the unit is active.
- Water Purification: The purifier will automatically begin purifying water and filling its 8-liter storage tank.
- Dispensing Water: Place a clean container under the water outlet. Press the dispense button or lever to release purified water.
- Copper Infusion: The purifier is designed to enrich water with copper. This process occurs automatically during purification.
- Indicator Lights: Pay attention to the indicator lights on the unit. These provide information on power status, purification progress, and filter life. Refer to the specific indicator guide provided by the manufacturer for detailed explanations.
6. Maintenance and Care
Regular maintenance ensures optimal performance and longevity of your purifier.
- External Cleaning: Wipe the exterior of the purifier with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Tank Cleaning: Periodically drain and clean the storage tank as per manufacturer guidelines to prevent biofilm buildup.
- Filter Replacement: The purifier contains multiple filters and a GermKill Kit (GKK) that require periodic replacement. The frequency depends on water quality and usage. Refer to the service schedule or indicator lights for timely replacement. Contact authorized service personnel for filter changes.
- Service Schedule: Adhere to the recommended service schedule to ensure the purifier functions effectively and maintains water quality.
7. Troubleshooting Guide
This section addresses common issues you might encounter. For problems not listed here, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| No water dispensing | No power; water supply off; tank empty; clogged filter. | Check power connection; ensure water supply is on; wait for tank to fill; contact service for filter inspection. |
| Slow water flow | Low water pressure; partially clogged filter. | Check input water pressure; contact service for filter inspection/replacement. |
| Unusual taste/odor in water | Expired filters; dirty tank. | Replace filters/GKK; clean the storage tank. |
| Leakage from unit | Loose connections; damaged component. | Immediately turn off water supply and power. Contact service technician. |
8. Product Specifications
| Brand | Pureit |
| Model Name | WUCU200 |
| Special Features | RO, UV, MF, Copper+ Enrichment |
| Purification Stages | 7-stage purification process |
| Capacity | 8 Liters |
| Installation Type | Freestanding |
| Power Source | MANUAL |
| Supported Water TDS Level (Max) | 500 PPM |
| Item Weight | 12.12 Kilograms |
| Product Dimensions (LxWxH) | 17.6 x 13.78 x 14.21 cm |
| Manufacturer | Hindustan Unilever |
9. Warranty and Customer Support
For warranty details, please refer to the warranty card provided with your product at the time of purchase. The warranty typically covers manufacturing defects under normal use conditions.
For technical assistance, service requests, or to purchase genuine replacement parts, please contact Pureit customer support. Contact information can usually be found on the product packaging or the official Pureit website.
